Free US shipping90-day free returns · prepaid labelFit Guarantee · how it works
Shootbolt Instant identifierIdentify part

HOPPE part numbers: how to read the stamp and order the right part

By · · Updated

Short answer: a HOPPE part number, such as 3622876, is a plain 6- to 8-digit item number that tells you nothing by itself. The meaning is in the coded description printed beside it, such as M/45/25 914 SW1SB1 620 16S 20. Read that code left to right: mode, backset, deadbolt throw, handle height, locking points, point position, faceplate and a last size.

At a glance
  • Where the number is: the box label or door paperwork, not the faceplate
  • What the faceplate shows: the HOPPE logo between the latch and the deadbolt
  • No label? Measure the door and build the code (worked example below)

Part number, code or seller shorthand?

You may meet three kinds of HOPPE number; only the coded description tells you what the part is (Figure 1). The short version is in the HOPPE multipoint lock guide.

Three numbers you may find for a HOPPE gear: the part number, the coded description and seller shorthand Three numbers, one gear: which tells you what it is? HOPPE part number 3622876 6 to 8 digits You order with it The digits mean nothing HOPPE coded description M/45/25 914 SW1SB1 620 16S 20 Printed beside the number Every token is a size or choice This one tells you the part Seller shorthand 45/92/25 Backset / handle-to-key spacing / deadbolt throw Not a HOPPE number The faceplate on the door edge shows the HOPPE logo, not these numbers. Look for the number and code on the box label or the door paperwork.
Figure 1. Only the coded description tells you what the part is. You order with the part number.
  • Part number (3622876): what you order with. The digits mean nothing.
  • Coded description (M/45/25 914 SW1SB1 620 16S 20): HOPPE prints no key to it, but each token sits under a labeled column in its HLS 9000 catalog tables[1]. HOPPE's website writes it with slashes: M/45/25 / 914 / SW1SB1 / 620 / 16-SC / 20[3].
  • Seller shorthand (45/92/25): backset, handle-to-cylinder spacing and deadbolt throw. Useful, but not a HOPPE number.

What the HOPPE stamp on the faceplate tells you

The stamp names the maker, not the part. HOPPE's replacement questionnaire first asks whether the faceplate logo, between the latch and the deadbolt, reads HOPPE, FUHR or something else, then its finish and width[2]. Shine a flashlight along the open door's edge (Figure 2).

Close-up of a stainless lock faceplate out of the door, with the HOPPE logo stamped on it and circled.
Figure 2. The stamp names the maker. The part number is on the box label or door paperwork, not here. Shown: a HOPPE faceplate out of the door.

No HOPPE document we hold says a part number is stamped on the faceplate or gear case, so look on the box label (Figure 3) or door paperwork, or fill in HOPPE's questionnaire. A FUHR logo means another maker: see Fuhr multipoint locks. No logo: which multipoint lock do I have?

ILLUSTRATION, NOT A PHOTO OF A REAL LABEL HOPPE Part number 3622876 Coded description M/45/25 914 SW1SB1 620 16S 20 You order with the part number. The code tells you what the part is.
Figure 3. Illustration, not a photo. Look for these two things on any box label or paperwork you kept; a real label may look different.

Every segment of a HOPPE gear code

The tokens run in a fixed order, each under a labeled catalog column[1].

Segment Example Means Other values
Mode M Manual: lift the handle to lock A automatic; IA second door of a pair; E electronic
Backset /45 1-3/4 in (45 mm) 35, 60, 70
Deadbolt throw /25 1 in (25 mm) 14 = 9/16 in (14 mm)
Handle height 914 36 in (914 mm), door bottom to handle center All 2019 catalog gears read 914
Locking points SW1SB1 Swing hook plus shootbolt TN tongue, RL roller, RB roundbolt; digit = count
Position 620 Lower point 24-7/16 in (620 mm) below the handle center 671, 753, 750, 668, 400/750
Faceplate 16S 5/8 in (16 mm), square ends 16R rounded; 20S 3/4 in (20 mm)
Last number 20 Shootbolt throw, 3/4 in (20 mm) 25 = 1 in (25 mm) throw; on gears without a shootbolt, the most you can cut off the bottom

Two segments catch people. The position counts down from the handle: 914 minus 620 leaves about 11-9/16 in (294 mm) up from the door bottom. And the last number changes meaning: 20 on a shootbolt gear is the bolt's throw, 160 on a tongue gear is trim allowance. The handle-to-cylinder spacing isn't in the code; HOPPE's handle catalog draws it as 3-5/8 in (92 mm)[5].

HLS 9000 gear versions and their codes

Each HLS 9000 version has its own token and fixed positions[1]. Most come in all four backsets; two-roller, four-roller and automatic gears in 35 and 45 only.

Version Token Position Faceplate Last number
Tongue TN1 620, 671, 753 16S, 20S Cutoff 160, 115, 30
Tongue + shootbolt TN1SB1 620 16S, 20S Throw 20
Swing hook SW1 753 16S None
Swing hook + shootbolt SW1SB1 620 16S Throw 20
Shootbolt SB1 None 16S, 20S Throw 20
Two roller / four roller RL1 / RL2 750 / 400/750 16S Cutoff 60
Roller + shootbolt RL1SB1 620 16S Throw 20
Roundbolt / + shootbolt RB1 / RB1SB1 668 / 620 16S Cutoff 140 / throw 20
Automatic tongue / two roller A … TN1 / RL1 671, 753 / 750 16S Cutoff 115, 30 / 60
Second door IA … SB1 None 16S, 20S Throw 20 or 25

A two-roller lock has one roller on the gear and one on the top extension. Website codes for second-door gears end in 1384, which HOPPE's printed catalogs leave out, so don't match on it. Point shapes: types of multipoint locking points.

Extension and handle-set codes

Extension codes give mode, length in mm, then points and positions. HOPPE's catalog lists top extension 8778611 as M 400 SB1 16S 20 100: 15-3/4 in (400 mm) long, a shootbolt with 3/4 in (20 mm) throw, and up to 3-15/16 in (100 mm) to trim[1]. Handle sets read lever/plate: München M112PL/374N is lever M112PL on plate 374N, and a finish code like F42-R follows, where -R marks HOPPE's Resista finish[5]. See multipoint handle sets.

HLS 7 and HLS One numbers

HLS 7 codes add the hand after the handle height: M/45/25 914 LI SWS 620 16S 25 (2666498) is left-hand; RE is right-hand. HOPPE's HLS 7 sheet still lets you re-hand one by moving two case screws and reversing the latch[6]. HLS One kits carry pack numbers with no code, picked by door height and backset; 3210661 is the 3-point tongue pack for a single 6 ft 8 in (2,032 mm) or 7 ft 0 in (2,134 mm) door with a 1-3/4 in (45 mm) backset[7]. The HLS 7 is still in HOPPE's catalog and an HLS 9000 gear doesn't replace it: replace like for like. We stock neither.

Where HOPPE's own sheets differ

What One HOPPE sheet says Go by
TN token Tongue-page legend: "TN1 = one swing hook"[4] Tongue: the catalog lists every TN code under tongue
Throw 14 Questionnaire: 1/2 in[2] 9/16 in (14 mm); the catalog prints 0.55 in
Faceplate 20S Questionnaire: 25/32 in 3/4 in (20 mm)
Roundbolt gear last number Catalog code: 20 Website: 140 cutoff[8]

Worked example: from your door to part 3622876

A swing hook and shootbolt door with no label: build the code with the door open, measuring from the door bottom, not the floor (Figure 4).

Measuring a swing hook and shootbolt door to build HOPPE code M/45/25 914 SW1SB1 620 16S 20 From the door edge to the code (lower half of the lock) bottom of the door 36 in (914 mm) handle height 11-9/16 in (294 mm) up 914 − 294 = 620 HOPPE counts down from the handle center Handle center Latch Deadbolt: 1 in → /25 Swing hook → SW1 Shootbolt into sill 3/4 in (20 mm) throw→ SB1 … 20 Code: M/45/25 914 SW1SB1 620 16S 20 → HOPPE part 3622876
Figure 4. Measure from the door bottom, then subtract from the handle height to get HOPPE's position number.
  1. Stamp and key: HOPPE logo, key below the handle: an HLS 9000.
  2. Mode: you lift the handle to lock: M.
  3. Backset: 1-3/4 in (45 mm): /45 (how to measure backset).
  4. Deadbolt throw: 1 in (25 mm): /25.
  5. Handle height: 36 in (914 mm): 914.
  6. Points: a hook below the handle and a shootbolt into the sill: SW1SB1. Hook center 11-9/16 in (294 mm) up: 914 − 294 = 620.
  7. Faceplate: 5/8 in (16 mm), square ends: 16S.
  8. Shootbolt throw: 3/4 in (20 mm): 20.

That gives M/45/25 914 SW1SB1 620 16S 20, which HOPPE's catalog lists as part 3622876[1]: our HOPPE HLS 9000 swing hook + shootbolt gear in the 1-3/4 in (45 mm) backset. Whether you need just the gear: which HOPPE gear you need.

Parts for this fix

When to call a pro

Call a locksmith who works on multipoint doors if a measurement falls between HOPPE's positions, the handle sits well off 36 in (914 mm), or there's no logo and nothing matches: it may be a special build or another make. The swap is in how to replace a multipoint door lock.

Common questions

Where is the part number on a HOPPE multipoint lock?

Usually on the box label or the door maker's paperwork, printed with a coded description such as M/45/25 914 TN 620 16S 160. The faceplate on the door edge carries the HOPPE logo between the latch and the deadbolt, and HOPPE's documents don't say a part number is stamped there. No label? Measure the door and build the code, or fill in HOPPE's replacement questionnaire.

What does 45/92/25 mean on a HOPPE gearbox?

It's seller shorthand, not a HOPPE part number: 1-3/4 in (45 mm) backset, 3-5/8 in (92 mm) handle-to-cylinder spacing and a 1 in (25 mm) deadbolt throw. HOPPE's own code adds the handle height, locking points, their position and the faceplate, as in M/45/25 914 SW1SB1 620 16S 20 for part 3622876.

What do TN, SW, SB, RL and RB mean in a HOPPE code?

They are the locking points: TN tongue, SW swing hook, SB shootbolt, RL roller and RB roundbolt. A digit gives the count, so RL2 is two rollers, and combinations run together, so SW1SB1 is a swing hook plus a shootbolt. HOPPE's website legend on its tongue pages calls TN a swing hook, but its catalog tables list every TN code under tongue.

Why does the HOPPE code say 620 when my hook is near the bottom of the door?

HOPPE measures locking-point positions down from the handle center, not up from the floor. Subtract the number from the handle height: with a 36 in (914 mm) handle, 914 minus 620 leaves about 11-9/16 in (294 mm) up from the door bottom. Measure from the bottom edge of the door, not the floor or the sill.

Is the last number in a HOPPE gear code a length?

It depends on the gear. On a gear with a shootbolt, such as SW1SB1 or TN1SB1, the last number is the shootbolt throw: 20 is 3/4 in (20 mm) and 25 is 1 in (25 mm). On tongue, roller and roundbolt gears it is the most you can cut off the bottom extension, such as 6-5/16 in (160 mm). Swing hook gears have no last number.

Sources

  1. HLS 9000 Multipoint Swing Door Hardware, Edition 7, 12/2019 (archived), HOPPE
  2. HLS Multipoint Hardware Door Replacement Questionnaire, 04/2016 (archived), HOPPE
  3. Swing Hook + Shootbolt product page (spec table, read 2026-10-19), HOPPE North America
  4. Tongue product page (spec table and legend, read 2026-10-19), HOPPE North America
  5. HLS 9000 Swing Door Handle Catalogue, 11/2019 (archived), HOPPE
  6. HLS 7 Series Multipoint Hardware System, Edition 3, 02/2020 (archived), HOPPE North America
  7. HLS One Catalog/Brochure, 01/2020 (archived), HOPPE North America
  8. Roundbolt product page (spec table, read 2026-10-19), HOPPE North America

Help identify my part

Send the part number, measurements or photos of your old hardware. We’ll review your request and reply by email within 1 business day.

Your photos are stored privately and used to help identify your part. Privacy policy