- Bolt type
- Tongue
- Faceplate width
- 5/8" (16 mm)
- Operation
- Lift handle to lock
79 products · 815 versions
HOPPE Multipoint Lock Replacement Parts
HOPPE multipoint lock replacement parts for HLS 9000 locks: gearboxes, extensions, strikes, cylinders, handle sets and hinges.
Not sure which part? Use our instant part identifier
- Gearboxes 15
- Extension rods 15
- Strike plates 11
- French door flush bolts 6
- Spindles & small parts 10
- Euro cylinders 6
- Bolt type
- Shootbolt
- Faceplate width
- 3/4" (20 mm) / 5/8" (16 mm)
- Operation
- Lift handle to lock
- Bolt type
- Tongue + Shootbolt
- Faceplate width
- 3/4" (20 mm) / 5/8" (16 mm)
- Operation
- Lift handle to lock
- Bolt type
- Tongue
- Faceplate width
- 5/8" (16 mm)
- Operation
- Locks as the door closes
- Door
- 5 options
- Lock family
- HLS 9000
- Door
- 3 options
- Lock family
- HLS 9000
- Door
- 5 options
- Lock family
- HLS 9000
- Door
- 5 options
- Lock family
- HLS 9000
- Faceplate width
- 5/8" (16 mm)
- Backset
- 1-3/4" (45 mm) / 1-3/8" (35 mm) / 2-3/4" (70 mm) / 2-3/8" (60 mm)
- Lock family
- HLS 9000
Before you order: 3 checks
HOPPE calls the gearbox the gear and sellers also call it the lock case, a strike is also called a keeper, a handle set is also called trim, and the lock family is written HLS 9000 or HLS9000.
Lock it with the door open
Open the door, hold in the trigger (the small spring plunger beside the latch), lift the handle and turn the thumb-turn. If it locks easily with the door open but not shut, the door is out of line with its frame and the lock is not the part, so look at the strike plates and the hinges first. Turn the thumb-turn back and push the handle down, so every bolt is in before you close the door.
Loose handle? Tighten the set screw
A loose handle wobbles but still springs back level. Tighten the set screw under the lever, often with a 3 mm hex key on HOPPE. A handle that still rests below level once tight has a weak or broken return spring, which can be in the handle set or in the gearbox.
Key above the handle? That is not HLS 9000
The parts on this page are for HOPPE HLS 9000 locks, which have the key cylinder below the handle. A round key cylinder above the handle is a HOPPE HLS 7, a different system that an HLS 9000 gearbox will not replace. We do not stock HLS 7 gearboxes.
Replacement parts for HOPPE HLS 9000 locks
How to tell you have a HOPPE lock
Open the door and look at the metal strip on its edge: a HOPPE lock carries the HOPPE name there, and HOPPE handle sets for HLS 9000 locks have 3-5/8" (92 mm) between the handle and the cylinder hole. The part number is on the box label or the door's paperwork, not on the lock. Search a number, current or old, and we find the part it maps to. No number? The part finder asks what you see.
The HLS 9000 system
HOPPE's HLS 9000 is built from pieces: a gearbox behind the handle, top, middle and bottom extensions with the locking points, strikes on the frame and a Euro profile cylinder. Because it is sold in pieces, you can replace only the one that failed. It comes manual or automatic, with tongue, roller, roundbolt, swing hook or shootbolt locking points, and as a single-point lock.
Handles, hinges and the rest
HOPPE also makes the handle sets that sit on these locks, among them München, Verona and Dallas, the Dallas 4600 handles for sliding patio doors, and adjustable hinges. Every part on this page is listed with its HOPPE part numbers, old ones included.
Guides for this page
Written from the manufacturers' own catalogs and installation sheets.
- HOPPE multipoint locks (HLS 9000): a plain-English guideWhich lock you have, how it works and what wears out.
- HOPPE part numbers: how to read the stampWhat each part of the code on the label means.
- Door lock backset: how to measure itThe measurement most orders depend on.
- Kolbe door hardware
- Sierra Pacific door locks
- Therma-Tru door handles
Questions
Where can I buy HOPPE replacement parts in the US?
Here, for HLS 9000 locks. Shootbolt sells replacement parts for HOPPE HLS 9000 multipoint locks: gearboxes, extensions, strikes, Euro profile cylinders, handle sets and adjustable hinges. Every part is listed with its HOPPE part numbers, old ones included, and every order ships free in the US with 90-day free returns. We do not stock HLS 7 gearboxes or HLS One kits. Not sure which part you need? Use our instant part identifier before you order.
How do I tell if my lock is a HOPPE?
Open the door and look at the metal strip on its edge. A HOPPE lock has the HOPPE logo there, between the latch and the deadbolt. The logo names the maker only, because HOPPE does not print part numbers on the parts. Then look at the key: on an HLS 9000 the keyhole-shaped cylinder is 3-5/8" (92 mm) below the handle. Other makers use that spacing too, so the logo is the proof. No logo? The instant part identifier asks what you see.
What is the difference between HOPPE HLS 9000, HLS 7 and HLS One?
The key position, and how the lock is sold. HLS 9000 has a Euro profile cylinder below the handle and is sold part by part. HLS 7 has a round US-style cylinder above the handle. HLS One is a boxed kit with the lock, strikes and screws in one package, and HOPPE says any HLS 9000 swing-door handle set may be used with it. Parts on this page are for HLS 9000. We do not stock HLS 7 gearboxes or HLS One kits. The HOPPE guide compares all three.
Can I replace one part of a HOPPE multipoint lock, or do I need the whole lock?
Usually one part. HOPPE's HLS 9000 is sold in pieces: a gearbox behind the handle, extensions with the locking points, strikes, a Euro profile cylinder and a handle set. The gearbox is usually the part that fails. It comes as one part with the lower extension, so the top of the lock, the handles, the cylinder and the strikes stay on the door, and the swap takes about 20 minutes. Replace the whole lock when the faceplate is bent across the joint or the top section is broken.
Which door brands use HOPPE multipoint locks?
Door makers buy their locks from other companies, so the door brand is a clue, not proof. We have a source for three. Therma-Tru's multipoint lock installation instructions cover the HOPPE HLS 9000. Kolbe says it offers HOPPE multipoint hardware on four of its swinging door series. A 2020 trade article says Sierra Pacific uses mainly HOPPE. Check for the HOPPE logo on the door edge before you order. Guides: Therma-Tru, Kolbe, Sierra Pacific.
Where is the part number on a HOPPE lock?
On the box label or in the paperwork that came with the door, not on the lock. HOPPE does not print part numbers on the parts themselves, and the HOPPE logo on the faceplate names the maker only. A HOPPE part number is a plain 6- to 8-digit number, such as 8779123. Search it here, current or old, and we find the part it maps to. No number? Use our instant part identifier, or read how HOPPE part numbers work.
Every order: free US shipping · 90-day free returns with a prepaid label · if our part identifier said it fits and it doesn't, we pay the return. Shipping · Returns










