Free US shipping90-day free returns · prepaid labelFit Guarantee · how it works
Shootbolt Instant identifierIdentify part

Sierra Pacific door handles and hardware

By · · Updated

Short answer: Sierra Pacific swinging and sliding doors use a stainless steel multipoint lock with forged brass door handles. A 2020 trade article says Sierra Pacific uses mainly HOPPE locks. Read the stamp on the metal strip along the door edge (the faceplate): a HOPPE HLS 9000 takes HOPPE parts by measurement, and anything else goes to Sierra Pacific's Parts Center.

At a glance
  • Swinging doors: stainless steel multipoint lock as standard
  • Lock maker: mainly HOPPE (2020 trade article); the stamp decides
  • Handle names: Dallas, München, Verona, Toronto and Rodos are HOPPE names too
  • Sliding doors: multipoint too; lock maker not named
  • Other parts: Sierra Pacific's Parts Center

What hardware do Sierra Pacific doors use?

Sierra Pacific doors, patio doors included, use a multipoint lock: one handle locks the door at several points along its edge. Sierra Pacific's hardware page says its swinging doors come standard with a 300 series stainless steel multipoint lock, handle sets and coordinating hinges[1]. Sliding doors get one too[2]; handles and plates are forged solid brass[3].

Sierra Pacific door Lock maker Evidence and how sure
Swinging door Mainly HOPPE 2020 trade article[4]; Sierra Pacific's own "Hoppe Hardware: Trim Set Installation" video[5]. Likely, not certain
Swinging door, Wisconsin-built (WI) line Possibly G-U One parts seller's video lists a G-U lock for these. Weak: check the stamp
Sliding patio door Not stated Genoa and Verona handles[2]. Check the stamp

GreenBuildingAdvisor's 2020 review found Sierra Pacific "uses primarily Hoppe"[4]. Primarily isn't always, so check your stamp.

Which lock is in your Sierra Pacific swinging door?

The Sierra Pacific name doesn't tell you the lock. Open the door and read the logo and number stamped on the faceplate near the latch (Figure 1 shows the route, Figure 2 the stamp).

Which lock is in a Sierra Pacific door, and where to get its parts Sierra Pacific door: which lock, and where its parts come from Swinging or sliding door? Hinged doors swing; patio sliders glide Swinging door Mainly HOPPE (2020 trade article) Key usually below the handle Sliding patio door Multipoint lock, maker not named Open the door: read the stamp on the faceplate near the latch HOPPE HLS 9000 Order HOPPE parts by measurement Other stamp, no stamp, or slider parts: Sierra Pacific's Parts Center request form (send photos; ask first if under warranty)
Figure 1. The trade article says mainly HOPPE; the faceplate stamp on your door decides where the parts come from.

Emtek's trim chart puts Sierra Pacific in its group with a keyhole-shaped cylinder (euro cylinder) 3-5/8 in (92 mm) below the handle[6]. That is the HOPPE HLS 9000 layout[7]. If the stamp reads HOPPE, order by measurement with our self-serve HOPPE part finder, or by HOPPE part number. If you see another stamp, such as G-U, or no stamp at all, see which multipoint lock do I have.

Close-up of a stainless lock faceplate out of the door, with the HOPPE logo stamped on it and circled.
Figure 2. The stamp near the latch and deadbolt names the lock maker. The Sierra Pacific name on the door doesn't. Shown: a HOPPE faceplate out of the door.

Which handle sets fit a Sierra Pacific door?

A HOPPE handle set fits only if the lock in the door is a HOPPE HLS 9000. Sierra Pacific lists Dallas, New Orleans, München, Verona, Toronto and Rodos handles for swinging doors[1]. We stock HOPPE swinging sets under five of those names, all but New Orleans. The sliding Verona (2170) is a different handle. Before you order, match:

  • the lock: HOPPE on the faceplate, key below the handle;
  • door thickness: the Flexible Access door has 1-3/4 in (45 mm) panels[8]; measure yours;
  • plate width and shape: Sierra Pacific gives codes (216, 374), not widths; measure the old plate;
  • handle-to-cylinder spacing: center of the square handle-bar hole (spindle hole) to center of the cylinder hole (Figure 3);
  • the spindle: 5/16 in (8 mm) square on HOPPE.
A HOPPE lock case out of the door, with an arrow from the center of the square handle hole to the center of the key cylinder hole, labeled PZ.
Figure 3. On a HOPPE HLS 9000 lock, the handle hole sits 3-5/8 in (92 mm) above the cylinder hole. Measure yours before you order. PZ is the trade name for this spacing.

HOPPE curved-lever sets (München, Toronto) come with one left and one right lever, so one set fits either door. Fit both levers pointing toward the hinges. Handle sets don't swap between lock brands. More in the HOPPE multipoint lock guide.

Sliding door handle? See how to replace a patio door handle.

Where do other Sierra Pacific door parts come from?

Sierra Pacific's Parts Center in Medford, Wisconsin, takes orders by a request form with photos[9]. Use it for:

  • sliding door locks, rollers and the Genoa handle;
  • hinges, weatherstrip, sills and panels;
  • any lock that isn't stamped HOPPE.

If the door may still be under warranty, ask Sierra Pacific first.

Does a worn lock mean a new door?

No. Test it with the door open first. Hold in the trigger, a small spring plunger beside the latch, then lift the handle and turn the key or thumbturn. If every bolt comes out smoothly, the lock works and the door is out of line: see door won't lock. Then turn the key or thumbturn back and push the handle down to retract every bolt before you close the door.

Parts for this fix

These fit only if the faceplate shows a HOPPE HLS 9000 and your measurements match. For which HOPPE gear to order, see HOPPE multipoint lock replacement; for the steps, how to replace a multipoint lock; for other door brands, multipoint lock replacement by door brand.

When to call a pro

Call a locksmith or your Sierra Pacific dealer if the door is locked shut and multipoint lock stuck closed doesn't free it, or the door is bowed or split. Don't pry at a locked multipoint: it bends the rods and strikes. If someone is locked in or there's an emergency, call 911. Only work on locks on your own door.

Common questions

What hardware do Sierra Pacific doors use?

Sierra Pacific swinging doors come standard with a 300 series stainless steel multipoint lock, handle sets in several finishes and coordinating hinges; a keyed lock is optional. Sliding doors also get a stainless multipoint lock, and the handles and plates are forged solid brass. A 2020 trade article says Sierra Pacific uses mainly HOPPE locks. The stamp on the metal strip along the door edge (the faceplate) tells you which lock is in yours.

Who makes the locks on Sierra Pacific doors?

Mostly HOPPE, according to a 2020 GreenBuildingAdvisor review of multipoint hardware, and Sierra Pacific's own video library includes a HOPPE trim set installation video. Sierra Pacific's product pages don't name the lock maker, and a parts seller lists a G-U lock for some Wisconsin-built doors. Read the logo stamped on the faceplate near the latch before you order; which multipoint lock do I have covers the rest.

Do HOPPE handle sets fit a Sierra Pacific door?

They can, if the lock in the door is a HOPPE HLS 9000 with the key below the handle. Sierra Pacific's Dallas, München, Verona, Toronto and Rodos handles share HOPPE names; we don't stock New Orleans. Match the door thickness, the plate width and shape (Sierra Pacific gives plate codes, not widths), the spindle-to-cylinder spacing and the 5/16 in (8 mm) spindle. Handle sets don't swap between lock brands.

Where can I get Sierra Pacific door replacement parts?

For a HOPPE HLS 9000 lock, order the gearbox, handles and cylinder by measurement with our self-serve HOPPE part finder; HOPPE multipoint lock replacement says which parts you need. For everything else, such as sliding door locks and rollers, hinges, weatherstrip, panels or a lock with another stamp, use the Sierra Pacific Windows Parts Center request form and send photos. If the door may still be under warranty, ask Sierra Pacific first.

How do I replace a Sierra Pacific sliding door handle?

Sierra Pacific doesn't name its sliding lock maker, so measure the screw-hole spacing and the door thickness, and read the stamp on the lock edge. For an exact match, use the Sierra Pacific Parts Center. The removal steps are in how to replace a patio door handle.

Sources

  1. Swinging door hardware, Sierra Pacific Windows
  2. Sliding door hardware, Sierra Pacific Windows
  3. What Makes Our Hardware So Easy To Love? (hardware sell sheet), Sierra Pacific Windows
  4. Multipoint Locking Hardware (Peter Yost, January 16, 2020), GreenBuildingAdvisor
  5. How-To-Service videos: Hoppe Hardware: Trim Set Installation, Sierra Pacific Windows
  6. 2022 Price Book: Multi-Point, Emtek
  7. HLS 9000 Multipoint Swing Door Hardware, Edition 7, 12/2019 (archived), HOPPE
  8. Flexible Access Outswing door, Sierra Pacific Windows
  9. Order Replacement Parts (Sierra Pacific Windows Parts Center), Sierra Pacific Windows

Help identify my part

Send the part number, measurements or photos of your old hardware. We’ll review your request and reply by email within 1 business day.

Your photos are stored privately and used to help identify your part. Privacy policy