Free US shipping90-day free returns · prepaid labelFit Guarantee · how it works
Shootbolt Instant identifierIdentify part

15 products · 153 versions

Multipoint Lock Extension Rods

Multipoint lock extension rods carry the bolts above and below the handle. Replace one when a top or bottom bolt won't throw.

Not sure which part? Use our instant part identifier

Filter
Not sure which part? Instant identifier or send us a photo.
Locking points
Locks the bolts
15 products

Before you order: 3 checks

HOPPE's catalog calls each of these an Extension (top, middle or bottom) and describes it as a section of the drive rail; this store also lists them as extension rods and top/bottom assemblies.

  1. Lock it with the door open

    Open the door, hold in the trigger (the small spring plunger beside the latch) and lift the handle; push it back down before you close the door. If every bolt moves but the lock will not work with the door shut, the door is out of line with its frame: look at the strike plates and the hinges first. If one bolt is bent, broken or stuck while the others move, the extension that carries it is often the part to replace.

  2. Top section or middle section?

    The same kind of bolt can sit on two different parts. A section at the top of the lock is a top extension; a section between the gearbox and a top extension is a middle extension, and it is a different part. Check too whether the lock is manual or automatic: automatic extensions go with automatic gearboxes.

  3. Do not order by the old length alone

    Top extensions are cut at the top when fitted, so a fitted one can measure shorter than its listed length, and a measured length can match a shorter, wrong part. Use the part number from the box label or the paperwork that came with the door if you have it. If not, measure each bolt's height from the center of the handle and the faceplate width, 5/8" (16 mm) or 3/4" (20 mm), or use the instant part identifier.

Compare the 15 extensions

What you choose on each page, how many versions it has and where its price starts. Every part number is in the list below.

PartYou chooseVersionsFrom
HOPPE top extension with tongue, manual, 1 or 2 tonguesFaceplate width: 5/8", 3/4" · Length & locking points: 13 choices19$59.99
HOPPE middle extension with tongue, manualFaceplate width: 5/8", 3/4" · Length & locking points: 9 choices12$46.78
HOPPE top extension with shootbolt, 3/4" (20 mm) throwFaceplate width: 5/8", 3/4" · Length & locking points: 8 choices14$79.99
HOPPE middle extension, connecting rod with no locking pointFaceplate width: 5/8", 3/4" · Length & locking points: 6 choices10$29.92
HOPPE top extension with tongue, automaticLength & locking points: 6 choices6$69.99
HOPPE top extension with roller, automaticLength & locking points: 5 choices5$69.99
HOPPE top extension with 2 rollers, manualLength & locking points: 8 choices8$79.99
HOPPE top extension with roller, 5/8" (16 mm) faceplateLength & locking points: 5 choices5$59.99
HOPPE top extension with round bolt, 5/8" (16 mm) faceplateLength & locking points: 11 choices11$139.99
HOPPE middle extension with swing hook, 5/8" (16 mm) faceplateLength & locking points: 5 choices5$89.99
HOPPE middle extension with roller, 5/8" (16 mm) faceplateLength & locking points: 6 choices6$40.53
HOPPE top extension with shootbolt, inactive second doorLength & locking points: 13 choices · Faceplate & shootbolt throw: 4 choices40$79.99
HOPPE middle extension with round bolt, 5/8" (16 mm) faceplateLength & locking points: 4 choices4$119.99
HOPPE top extension with swing hook, 5/8" (16 mm) faceplateLength & locking points: 6 choices6$109.99
HOPPE bottom extension with shootbolt, 17-1/16" (434 mm)Faceplate & shootbolt throw: 2 choices2$69.99
All 153 part numbers on this page

Top, middle and bottom extensions for multipoint locks

How the extensions work with the gearbox

HOPPE builds an HLS 9000 lock from pieces: the gearbox in the middle, a top extension and, on some locks, a middle or bottom extension. Each extension is a length of faceplate with a rod inside and its locking points at fixed heights. The gearbox drives the rods, so when you lift the handle every bolt along the door edge moves together. If one bolt is bent, broken or stuck while the others move, the extension that carries it is often the part to replace.

Length and locking points

Extensions are sold by length, and each length comes with its bolts at set heights. HOPPE gives each bolt's height from the center of the handle, so measure from the handle center to the middle of each bolt, then measure the old extension end to end. Gearbox length plus extension lengths gives the overall length of the lock. The product page lists every length with the bolts it carries, in inches first and millimeters in brackets.

Match the bolt type and faceplate

Order the bolt type the door has now: tongue, two or four rollers, roundbolt, swing hook, shootbolt, or a combination such as tongue plus shootbolt. Automatic extensions go with automatic gearboxes. The faceplate must match the gearbox, 5/8" (16 mm) or 3/4" (20 mm) wide. For the second door of a French pair, use the inactive door shootbolt extensions on the French door flush bolts page.

Choosing the right one

How to read the options you will see on these products.

Faceplate width

The long metal strip you see on the edge of the door when it's open. HOPPE makes it 5/8" (16 mm) or 3/4" (20 mm) wide. The gear and the extensions of one lock must have the same width.

How to measure: Measure straight across the metal strip on the door edge: about 5/8" means 16 mm; about 3/4" means 20 mm.

Length & locking points

HOPPE sells a multipoint lock in pieces: the gear (the middle part, with the handle and key) plus a top extension, and on some locks a middle or bottom extension. Gear length + extension lengths = the overall length. Each extension length comes with its locking points at fixed heights.

How to measure: Measure your old extension end to end. HOPPE gives each bolt's height from the center of the handle, so measure from the handle center up to the middle of each bolt.

Questions

Which extension rods do I need?

If you have the part number, from the box label or the paperwork that came with the door, search it above. HOPPE does not print part numbers on the parts themselves, so otherwise match the measurements in the guide above. Not sure? Use our instant part identifier to confirm the part before you order.

Can a multipoint lock extension be cut to length?

Top extensions, yes, up to HOPPE's limit. A HOPPE top extension is cut at the top when it is fitted, and HOPPE lists a maximum cut-off by version. On the top extension with shootbolt it is 3-15/16" (100 mm) on every version. On other top extensions the limit differs by version, and some versions list none, so check the product page before you order. HOPPE's catalog lists no cut-off for middle extensions, so order those by length.

How do I measure for a top extension?

Measure from the center of the handle, not from the bottom of the door. Count the bolts above the handle, then measure from the handle center up to the middle of each one. Measure the faceplate straight across: about 5/8" means 16 mm, about 3/4" means 20 mm. Treat the old extension's length as a cross-check only. Top extensions are cut at the top when fitted, so a fitted one can measure shorter than its listed length. Not sure? Use our instant part identifier.

Can I replace only the extension and keep my gearbox?

Usually. HOPPE builds an HLS 9000 lock from separate pieces, and each extension is sold on its own, without the gearbox or strikes. If one bolt is bent, broken or stuck while the others move, the extension that carries it is often the part to replace. The new one has to match the gearbox you keep: the same faceplate width, 5/8" (16 mm) or 3/4" (20 mm), the same bolt type, and automatic with automatic. A drooping handle usually points to the gearbox instead.

Do I need a middle extension?

Usually only on a main-door lock with a shootbolt at the top. On those HOPPE HLS 9000 locks a middle extension goes between the gearbox and the top extension, which carries the shootbolt. The middle section carries a tongue, roller, round bolt or swing hook, or it is a plain connecting rod with no bolt. Locks without a shootbolt are a gearbox plus a top extension. The shootbolt lock for the second door of a pair has no middle extension either.

What is the difference between a top extension and a shootbolt?

One is a section of the lock and the other is a bolt. A top extension is the upper section: a length of faceplate with a rod inside that attaches above the gearbox and reaches up the door. A shootbolt is a locking point. HOPPE describes it as an arrow-shaped bolt that extends into strike plates in the head and sill of the frame. Some top extensions carry a shootbolt; others carry a tongue, rollers, a round bolt or swing hooks.

Every order: free US shipping · 90-day free returns with a prepaid label · if our part identifier said it fits and it doesn't, we pay the return. Shipping · Returns

Help identify my part

Send the part number, measurements or photos of your old hardware. We’ll review your request and reply by email within 1 business day.

Your photos are stored privately and used to help identify your part. Privacy policy