- Operation
- Lift handle to lock
- Backset
- 1-3/4" (45 mm) / 1-3/8" (35 mm) / 2-3/4" (70 mm) / 2-3/8" (60 mm)
- Lock family
- HLS 9000
15 products · 116 versions
Multipoint Lock Gearboxes
Multipoint lock gearboxes are the case behind the handle. Replace one when the handle droops or won't spring back up. Sellers also call it a lock case, lock body or multipoint mortise lock; HOPPE's catalog calls it the gear.
Not sure which part? Use our instant part identifier
- Bolt type
- Tongue
- Faceplate width
- 5/8" (16 mm)
- Operation
- Lift handle to lock
- Bolt type
- Shootbolt
- Faceplate width
- 3/4" (20 mm) / 5/8" (16 mm)
- Operation
- Lift handle to lock
- Bolt type
- Tongue + Shootbolt
- Faceplate width
- 3/4" (20 mm) / 5/8" (16 mm)
- Operation
- Lift handle to lock
- Bolt type
- Tongue
- Faceplate width
- 5/8" (16 mm)
- Operation
- Locks as the door closes
- Bolt type
- Roller
- Faceplate width
- 5/8" (16 mm)
- Operation
- Locks as the door closes
- Bolt type
- Tongue
- Faceplate width
- 3/4" (20 mm)
- Operation
- Lift handle to lock
- Bolt type
- Roller
- Faceplate width
- 5/8" (16 mm)
- Operation
- Lift handle to lock
- Bolt type
- Roller
- Faceplate width
- 5/8" (16 mm)
- Operation
- Lift handle to lock
- Bolt type
- Swing hook
- Faceplate width
- 5/8" (16 mm)
- Operation
- Lift handle to lock
- Bolt type
- Roller + Shootbolt
- Faceplate width
- 5/8" (16 mm)
- Operation
- Lift handle to lock
- Bolt type
- Roundbolt
- Faceplate width
- 5/8" (16 mm)
- Operation
- Lift handle to lock
- Bolt type
- Shootbolt
- Faceplate width
- 3/4" (20 mm) / 5/8" (16 mm)
- Operation
- Lift handle to lock
- Bolt type
- Shootbolt + Swing hook
- Faceplate width
- 5/8" (16 mm)
- Operation
- Lift handle to lock
- Bolt type
- Shootbolt + Roundbolt
- Faceplate width
- 5/8" (16 mm)
- Operation
- Lift handle to lock
Nothing matches every filter.
Is it the gearbox? Three checks before you order
The cheaper causes come first. Each takes a couple of minutes with the door open.
Lock it with the door open
Open the door, hold in the trigger (the small spring plunger beside the latch), lift the handle and turn the thumb-turn. Turn it back and push the handle down, so every bolt is in before you close the door.
Locks easily open, but not shut?
The door is out of line with its frame, and the gearbox is not the part. Look at the strike plates and the hinges first.
Loose, or drooping?
A loose handle wobbles but still springs back level. Tighten the set screw under the lever, often with a 3 mm hex key on HOPPE.
Still rests below level once tight?
That is droop: a return spring is weak or broken. Go to check 3.
Push the bare spindle
Take the inside handle off. Push the square spindle down gently with your fingers and let go.
Springs back level?
The gearbox is working, so the handle set is the part.
Stays down?
On a HOPPE lock a worn gearbox is the likely cause.
Check 3 is a quick check locksmiths use, not a HOPPE instruction. A key that sticks, turns stiffly or spins points to the cylinder, not the gearbox.
Compare the 15 HOPPE HLS 9000 gearboxes
Find the row whose bolt below the handle matches yours. Every gearbox here works with a 3-5/8" (92 mm) handle-to-cylinder spacing.
| Gearbox | Bolt below the handle | Locks the bolts | Faceplate | Backsets | Whole lock is | Versions | From |
|---|---|---|---|---|---|---|---|
| Gearbox only (lock case) | None. The case fits onto the faceplate strip you have | When you lift the handle | Uses yours | 1-3/8", 1-3/4", 2-3/8", 2-3/4" | Your own extensions | 6 | $179.99 |
| Lower tongue, 5/8" faceplate | Tongue | When you lift the handle | 5/8" | 1-3/8", 1-3/4", 2-3/8", 2-3/4" | Gearbox + top extension | 16 | $159.99 |
| Lower tongue, 3/4" faceplate | Tongue | When you lift the handle | 3/4" | 1-3/8", 1-3/4", 2-3/8", 2-3/4" | Gearbox + top extension | 14 | $149.99 |
| Lower tongue, automatic | Tongue | As the door closes | 5/8" | 1-3/8", 1-3/4" | Gearbox + top extension | 7 | $139.99 |
| Lower tongue and shootbolt | Tongue + shootbolt | When you lift the handle | 5/8", 3/4" | 1-3/8", 1-3/4", 2-3/8", 2-3/4" | Gearbox + middle + top extension | 10 | $179.99 |
| Lower roller | Roller | When you lift the handle | 5/8" | 1-3/8", 1-3/4" | Gearbox + top extension | 4 | $159.99 |
| 2 lower rollers | 2 rollers | When you lift the handle | 5/8" | 1-3/8", 1-3/4" | Gearbox + top extension | 4 | $169.99 |
| Lower roller, automatic | Roller | As the door closes | 5/8" | 1-3/8", 1-3/4" | Gearbox + top extension | 4 | $169.99 |
| Lower roller and shootbolt | Roller + shootbolt | When you lift the handle | 5/8" | 1-3/8", 1-3/4", 2-3/8", 2-3/4" | Gearbox + middle + top extension | 6 | $169.99 |
| Lower swing hook | Swing hook | When you lift the handle | 5/8" | 1-3/8", 1-3/4", 2-3/8", 2-3/4" | Gearbox + top extension | 4 | $219.99 |
| Lower swing hook and shootbolt | Swing hook + shootbolt | When you lift the handle | 5/8" | 1-3/8", 1-3/4", 2-3/8", 2-3/4" | Gearbox + middle + top extension | 4 | $189.99 |
| Lower round bolt | Round bolt | When you lift the handle | 5/8" | 1-3/8", 1-3/4", 2-3/8", 2-3/4" | Gearbox + top extension | 4 | $199.99 |
| Lower round bolt and shootbolt | Round bolt + shootbolt | When you lift the handle | 5/8" | 1-3/8", 1-3/4", 2-3/8" | Gearbox + middle + top extension | 3 | $209.99 |
| Deadbolt and shootbolt | Shootbolt only | When you lift the handle | 5/8", 3/4" | 1-3/8", 1-3/4", 2-3/8", 2-3/4" | Gearbox + middle + top extension | 12 | $159.99 |
| Inactive gearbox, second door | Shootbolt (the second door of a pair) | When you lift the handle | 5/8", 3/4" | 1-3/8", 1-3/4", 2-3/8", 2-3/4" | 2 or 3 pieces, by version | 18 | $149.99 |
All 116 part numbers on this page
- Gearbox only (lock case)HLS9-Gearbox-35-14, HLS9-Gearbox-35-25, HLS9-Gearbox-45-14, HLS9-Gearbox-45-25, HLS9-Gearbox-60-25, HLS9-Gearbox-70-25
- Lower tongue, 5/8" faceplate2406346, 2406354, 2406362, 2406371, 2406389, 2406397, 2423904, 8778075, 8778143, 8778147, 8778159, 8778163, 8778167, 8778171, 8778183, 8779123
- Lower tongue, 3/4" faceplate2320948, 2320972, 2320981, 2332316, 2332324, 2332341, 2332359, 2332367, 2406400, 2406418, 2406434, 2406442, 2406451, 2406469
- Lower tongue, automatic8778243, 8778247, 8778267, 8778271, 8778287, 8778291, 8778303
- Lower tongue and shootbolt2400622, 2400649, 2400657, 2406477, 2406485, 2406506, 8778107, 8778263, 8778283, 8778311
- Lower roller8778223, 8778255, 8778279, 8778511
- 2 lower rollers8778883, 8778887, 8778891, 8778895
- Lower roller, automatic8778251, 8778275, 8778295, 8778307
- Lower roller and shootbolt2858511, 3924524, 8778835, 8778839, 8778843, 8778847
- Lower swing hook3868868, 3868876, 3868884, 3868892
- Lower swing hook and shootbolt3622876, 3660426, 3814747, 3868761
- Lower round bolt2942245, 2942253, 8778139, 8778259
- Lower round bolt and shootbolt2485283, 8778751, 8778755
- Deadbolt and shootbolt2185125, 2185133, 2185141, 2185150, 2406514, 2406522, 2406531, 2406549, 8778331, 8778335, 8778339, 8778343
- Inactive gearbox, second door1997447, 2074564, 2099201, 2139436, 2185176, 2185651, 2399983, 2406557, 2406565, 2406573, 2406581, 2406590, 2406602, 2406611, 3403999, 3761139, 8778155, 8778443
Gearbox replacement for multipoint locks
Match the locking points first
The gearbox is the middle section of the lock. It holds the latch, the deadbolt and the mechanism the handle and key turn, and it drives the extension rods above and below it. Open the door, lock it, and look at the bolts that come out of its edge: a flat tongue, a round roller, a pin that shoots up or down (a shootbolt), a round bolt or a swing hook. Each HOPPE HLS 9000 gearbox here is named after the locking points its lock uses, so pick the one whose bolts match yours. Automatic gearboxes lock the extra bolts as the door closes; manual ones lock them when you lift the handle.
Backset, faceplate and deadbolt throw
Three measurements pick the exact version. Backset is the distance from the face of the metal strip on the door edge to the center of the handle hole: 1-3/8" (35 mm), 1-3/4" (45 mm), 2-3/8" (60 mm) or 2-3/4" (70 mm). The faceplate is 5/8" (16 mm) or 3/4" (20 mm) wide and must match the extensions. The deadbolt throws 9/16" (14 mm) or 1" (25.4 mm). On tongue gearboxes the height of the lower bolt, measured from the handle center, matters too. Each product page asks only for the ones that differ.
Why the gearbox is usually the part that fails
The handle and key work the gearbox every time the door is locked, so it takes the most wear. A handle that droops, won't spring back up or needs force to lift, and a key that turns stiffly, usually point to the gearbox rather than to the bolts. Replacing it keeps the door, the extensions and the strikes you already have. The gearbox is sold on its own, without handles or cylinder, so the handle set and the cylinder you have can go back on.
Choosing the right one
How to read the options you will see on these products.
Backset
How far the handle sits from the edge of the door: from the face of the metal strip on the door edge (the faceplate) to the center of the handle hole. HOPPE HLS 9000 locks come in 1-3/8" (35 mm), 1-3/4" (45 mm, the standard), 2-3/8" (60 mm) and 2-3/4" (70 mm).
How to measure: Open the door. Measure from the face of the metal strip on the door edge to the center of the square handle spindle hole.
Throw
How far the bolt sticks out of the faceplate when it's locked. HOPPE dead bolts throw 1" (25.4 mm) or 9/16" (14 mm); shootbolts throw 3/4" (20 mm) or 1" (25.4 mm).
How to measure: Lock the door while it's open and measure how far the bolt sticks out past the faceplate.
Lower locking point
The bolt below the handle (tongue, roller, swing hook or round bolt). HOPPE gives its position from the center of the handle hole, down to the center of that bolt.
How to measure: With the door open, measure from the center of the handle hole down to the center of the bolt below it, and match HOPPE's figure. From the floor instead: with HOPPE's standard 36" (914 mm) handle height, the bolt sits 36" minus that figure above the bottom of the door.
Faceplate width
The long metal strip you see on the edge of the door when it's open. HOPPE makes it 5/8" (16 mm) or 3/4" (20 mm) wide. The gear and the extensions of one lock must have the same width.
How to measure: Measure straight across the metal strip on the door edge: about 5/8" means 16 mm; about 3/4" means 20 mm.
Build
• 2-piece: gear + top extension. • 3-piece: gear + top extension + bottom extension (the bottom extension is sold separately).
Guides for this job
Written from the manufacturers' own catalogs and installation sheets.
Questions
Which gearbox do I need?
The one whose bolts match your lock. Look at the bolt below the handle (a tongue, roller, round bolt or swing hook) and whether a shootbolt shoots out of the top or bottom of the door. Then three measurements pick the version: backset, faceplate width and deadbolt throw. If you have a part number, from the box label or the door's paperwork, search it; HOPPE does not print part numbers on the parts themselves. Not sure? Use our instant part identifier before you order.
Can I replace just the gearbox on a multipoint lock?
Usually. On a HOPPE HLS 9000 the gearbox comes as one part with the lower extension and its bolt. The extension above hooks into it, so the top of the lock, the handles, the cylinder and the strikes stay on the door. If only the case has failed and the faceplate strip is straight, the gearbox only (lock case) fits onto the strip you have. Replace the whole lock when the faceplate is bent across the joint or the top section is broken.
Are multipoint lock gearboxes universal?
No. A gearbox has to match the maker of the lock, the bolts it drives, the backset, the faceplate width, the deadbolt throw and the handle-to-cylinder spacing, which is 3-5/8" (92 mm) on HOPPE HLS 9000. Every gearbox on this page is HOPPE HLS 9000. A different name on your faceplate needs that maker's part.
How do I know my backset without taking the lock out?
Open the door and measure from the face of the metal strip on the door edge to the center of the square handle spindle hole. HOPPE HLS 9000 backsets are 1-3/8" (35 mm), 1-3/4" (45 mm), 2-3/8" (60 mm) and 2-3/4" (70 mm). How to measure backset shows it step by step.
What do the numbers 45/92 on a gearbox mean?
Sellers write gearboxes as backset/handle spacing/throw in millimeters. 45/92/25 is a 1-3/4" (45 mm) backset, a 3-5/8" (92 mm) handle-to-cylinder spacing and a 1" (25.4 mm) deadbolt throw.
Why does my door handle droop?
A handle droops when its return spring is weak or broken, or when friction is beating it. On a multipoint door the spring can be in the handle set, in the gearbox, or both. Rule out the free causes first: a loose set screw, or the handle shaft rubbing the hole in the door. Then push the bare spindle (check 3 above) to see which part has lost its spring.
How long does it take to replace a multipoint gearbox, and what tools do I need?
About 20 minutes, with the door open. You need a hand Phillips screwdriver, hex keys (often 3 mm on HOPPE) and a board to lay the old and new parts side by side. Don't use a power driver. On a gearbox that comes with its lower extension, leave every Torx or tri-wing screw in the case alone: they hold it together under spring pressure. Swapping the lock case only also takes a #3 tri-wing bit, because the old case comes off the faceplate strip.
Every order: free US shipping · 90-day free returns with a prepaid label · if our part identifier said it fits and it doesn't, we pay the return. Shipping · Returns














