Free US shipping90-day free returns · prepaid labelFit Guarantee · how it works
Shootbolt Instant identifierIdentify part

HOPPE multipoint locks (HLS 9000): a plain-English guide

By · · Updated

Short answer: a HOPPE multipoint lock is a door lock from HOPPE North America of Fort Atkinson, Wisconsin, that bolts a hinged door at several points from one handle. Most are the HLS 9000: lift the handle, then turn the key or thumbturn below it. The HLS 7 puts a round key above the handle; HLS One is a boxed kit.

At a glance
  • Who makes it: HOPPE North America, part of the family-owned HOPPE Group (founded 1952, based in Switzerland), with a plant in Fort Atkinson, Wisconsin
  • The common one: HLS 9000: keyhole-shaped (euro) cylinder below the handle, 3-5/8 in (92 mm) from the handle center, stainless steel, made in the US
  • Tell which you have: HOPPE logo on the faceplate near the handle; key below the handle = HLS 9000, round key above = HLS 7
  • To order a part: backset, deadbolt throw, handle height, faceplate width, and the type and position of each locking point
  • Before you buy: a lock that works with the door open is fine; the door is out of line. Test open first (troubleshooting)

What is a HOPPE multipoint lock?

A HOPPE multipoint lock is a long lock set into the edge of a hinged door that locks it at the handle and at points above and below. Its US arm, HOPPE North America, has its plant and offices in Fort Atkinson, Wisconsin. HOPPE's company page says it belongs to the HOPPE Group, a family-owned company founded in 1952 and based in Switzerland[7].

In the US the name almost always means the HLS 9000 system. HOPPE's HLS 9000 catalog sells it as all stainless steel, made in the United States, salt-spray tested for 3,000 hours and used on the Florida coast, the Caribbean and Hawaii[1].

You find it on fiberglass, wood and clad entry doors, French doors and hinged patio doors. A US distributor quoted in Locksmith Ledger names HOPPE and G-U as the most popular multipoint locks in the country[8].

New to multipoint locks? Start with what a multipoint lock is and how it works.

HLS 9000, HLS 7 or HLS One: which HOPPE lock do you have?

If the key goes into a keyhole-shaped cylinder below the handle, it's an HLS 9000 (or an HLS One, which uses the same handle sets). If a round, American-style key cylinder sits above the handle, in the same plate, it's an HLS 7 (Figure 1). Then open the door and read the faceplate near the handle for the HOPPE logo.

Telling a HOPPE HLS 9000 from an HLS 7 by where the key goes Outside of the door: where does the key go? 3-5/8 in (92 mm) HLS 9000 (and HLS One) Keyhole-shaped euro cylinder BELOW the handle HLS 7 Round US-style cylinder ABOVE the handle, quarter turn Then confirm with the HOPPE logo on the faceplate in the door edge.
Figure 1. Key below the handle: HLS 9000 or HLS One. Round key above: HLS 7. Confirm with the faceplate logo.
Feature HLS 9000 HLS 7 HLS One
What it is HOPPE's main multipoint system, sold part by part American-style system A pre-packed kit: lock, strikes and screws in one box
Key cylinder Euro profile (keyhole-shaped), below the handle[1] US-style round cylinder above the handle, quarter turn so you can see locked or unlocked from across the room[2] As HLS 9000: any HLS 9000 swing-door handle set fits[3]
Backsets 1-3/8, 1-3/4, 2-3/8 or 2-3/4 in (35, 45, 60, 70 mm) 1-3/4 in (45 mm) 1-3/4 or 2-3/8 in (45 or 60 mm)
Handing Gears aren't handed: reverse the latch and the trigger Ordered by hand (LI/RE); re-hand by moving two case screws, then reversing the latch Latch and trigger reverse
Inside handle Unlock key or thumbturn first, then handle down One push down retracts every bolt, deadbolt included As HLS 9000
Versions Manual, automatic and second-door (inactive) Manual and second-door only 3-point tongue, 3-point shootbolt, 5-point tongue and shootbolt
How it's sold Part by part; we stock gears, extensions, strikes, handle sets, cylinders Not stocked here As kits (not stocked here); HLS 9000 handle sets fit it

HOPPE's HLS 7 catalog lists features the HLS 9000 doesn't have: anti-back-drive (the points resist being forced back from outside), a latch blocker on the second door of a pair, and simultaneous retraction from the inside handle. Its handles push onto the shaft with no set screw (Quick-Fit)[2]. HOPPE's HLS One catalog says the packs are built for 1-3/4 in (45 mm) thick doors with a 36 in (914 mm) handle height, in 6 ft 8 in (2032 mm), 7 ft (2134 mm) and 8 ft (2438 mm) door sizes; a 2-1/4 in (57 mm) door needs one extra latch and deadbolt strike (2014027) per active door[3].

Two rarer HOPPE locks: the electronic Multitronic, a FUHR design that HOPPE sells in North America[11], and side-lite gears for the narrow fixed panel beside an entry door. For other brands, use which multipoint lock do I have.

How to lock and unlock a HOPPE door

An HLS 9000 door locks in two moves, in the order on HOPPE's operating label[1]:

  1. Close the door fully. The latch holds it.
  2. Lift the handle all the way up. The hooks, tongues or bolts above and below the handle slide out into the frame.
  3. Turn the key or thumbturn. The deadbolt goes out and the handle can't be pushed down.
  4. To open: key or thumbturn back fully first, then handle down.

On an automatic HLS 9000 the points throw by themselves as the door closes, and you turn the thumbturn for the deadbolt[4]. On an HLS 7, turn the thumbturn to horizontal and lift the handle to lock; pushing the inside handle down pulls back the latch, deadbolt and every locking point at once[2].

Handle up is not locked. Finish with the key or thumbturn every time.

Which HLS 9000 do I have? Its parts and versions

An HLS 9000 lock has three sections on one faceplate. The gearbox (HOPPE calls it the gear) sits behind the handle and carries the latch, the deadbolt, the trigger (a small spring plunger beside the latch; HOPPE calls it the mishandling device) and the lower locking points on its bottom extension. A top extension carries the upper points, and tall doors add a middle extension. Toothed drive rails join the sections, with one Phillips screw at the joint. On the HLS 9000 the deadbolt is below the latch and the long cylinder screw goes through the faceplate below the deadbolt[6]. For every part by name, see multipoint lock parts explained.

HOPPE's HLS 9000 catalog lists these versions[1]. To find yours, match your points and faceplate width, then check the part number:

  • Manual, 5/8 in (16 mm) faceplate: swing hook, swing hook + shootbolt, tongue, tongue + shootbolt, shootbolt, roundbolt, roundbolt + shootbolt, two roller, roller + shootbolt, four roller.
  • Automatic: tongue, two roller and four roller.
  • Manual, 3/4 in (20 mm) faceplate: tongue, tongue + shootbolt, shootbolt.
  • Second door of a pair (inactive): shootbolt gears in both faceplate widths, plus flush-bolt rods for doors with no astragal.
  • Single point: latch and deadbolt only, no top and bottom points.

Each gear also comes in four backsets and two deadbolt throws: 9/16 in (14 mm) or 1 in (25 mm). A "3-point" HOPPE lock is two outer points plus the deadbolt; the latch and the trigger aren't counted. What each point does is covered in types of multipoint locks, and how points are counted in 3-point vs 5-point locks.

How to read a HOPPE part number

HOPPE part numbers are plain 6- to 8-digit item numbers such as 8779123, and the digits mean nothing. The meaning is in the coded description HOPPE prints beside each one. HOPPE doesn't publish a key to it, but every token lines up with a labeled column in its catalog tables[1]. Here is gear 8779123, M/45/25 914 TN 620 16S 160 (Figure 2). Check the label on any box you have too (Figure 3).

How to read the HOPPE gear code M/45/25 914 TN 620 16S 160 Reading a HOPPE gear code (part 8779123) M/45/25 914TN620 16S160 Modemanual (lift) Deadbolt throw1 in (25 mm) Point typetongue Faceplate5/8 in (16 mm), square Backset1-3/4 in (45 mm) Handle height36 in (914 mm) Lower point24-7/16 in (620 mm)below handle center Max cut-off6-5/16 in (160 mm)off the bottom The 7-digit part number carries no meaning; the code beside it does. A = automatic, IA = second door; SW swing hook, SB shootbolt, RL roller, RB roundbolt.
Figure 2. Every token in a HOPPE gear code is a measurement or a choice. The part number itself carries no meaning.
Token Means Other values you may see
M Manual: lift the handle, then turn the key or thumbturn A automatic; IA inactive (second door); E electronic
45 Backset 1-3/4 in (45 mm) 35, 60, 70
25 Deadbolt throw 1 in (25 mm) 14 = 9/16 in (14 mm)
914 Handle height 36 in (914 mm), door bottom to handle center Check yours; a few gears differ
TN Tongue locking point SW swing hook, SB shootbolt, RL roller, RB roundbolt; combined, e.g. SW1SB1
620 Lower point 24-7/16 in (620 mm) below the handle center 671, 753; two values like 400/750 for two points
16S Faceplate 5/8 in (16 mm), square ends 16R rounded ends; 20S 3/4 in (20 mm)
160 Up to 6-5/16 in (160 mm) can be cut off the bottom extension On shootbolt gears this is the shootbolt throw, 20 or 25

Websites write it with slashes, M/45/25 / 914 / TN1 / 620 / 16-SC / 160. On HLS 7 gears an extra token, LI or RE (German for left and right), gives the hand.

The position number trips people up. HOPPE measures locking-point positions down from the handle center, not up from the floor (Figure 4). To find where the point sits on your door, subtract it from the handle height in mm: 914 minus 620 leaves 294, so the point sits about 11-9/16 in (294 mm) up from the door bottom. With the same 36 in (914 mm) handle height, a 671 gear puts the lower point about 9-9/16 in (243 mm) up, and a 753 about 6-5/16 in (161 mm) up[1].

ILLUSTRATION, NOT A PHOTO OF A REAL LABEL HOPPE Part number 3622876 Coded description M/45/25 914 SW1SB1 620 16S 20 You order with the part number. The code tells you what the part is.
Figure 3. Illustration, not a photo. Look for these two things on any box label or paperwork you kept; a real label may look different.
HOPPE measures locking point positions down from the handle center HOPPE measures from the handle center, not the floor bottom of door handle center (the datum) lower tongue 620 in the code 24-7/16 in (620 mm) down from the handle handle height 36 in (914 mm) on your door: 914 − 620 = 294 about 11-9/16 in (294 mm) up 671 → about 9-9/16 in up; 753 → about 6-5/16 in up (with a 36 in handle height).
Figure 4. HOPPE's position numbers start at the handle center. Subtract them from the handle height to find the point on your door.

On your own door, tape from the bottom edge to the middle of each point and to the spindle center. Methods: standard door handle height and how to measure door lock backset.

Which doors have HOPPE locks?

Door makers buy locks, so the door brand is a clue, not proof. The faceplate stamp near the handle is proof (Figure 5).

Door maker What the evidence says How sure
Therma-Tru Therma-Tru's installation packet covers the HOPPE HLS 9000[6]; seller listings also show Ashland locks on Therma-Tru doors Check the stamp
Sierra Pacific A 2020 trade article says it uses "primarily Hoppe"[9] Likely
Kolbe Kolbe offers HOPPE swing-door hardware with the key below (European style) or above (American style)[10] Likely
Simpson Simpson's impact-rated data sheet (2023): "Hoppe 9000 or Endura Trillenium"[14]; its pivot-door page names a HOPPE multipoint[15]. Other Simpson doors carry whatever lock the prehanger fitted Sure for those doors; check the stamp on others
Loewen A Loewen dealer says HOPPE HLS 9000 is used on all 2-1/4 in (57 mm) terrace doors[16]. Loewen's handle styles (Dallas, Verona, Rodos) match HOPPE series names, but no Loewen document says HOPPE[17] Likely on 2-1/4 in doors; check the stamp
Hurd A parts seller lists HOPPE gears "for Hurd doors 2005 and prior", and G-U from 2006[18] Likely to 2005; G-U after
Weather Shield A distributor says current doors use HOPPE; doors built before about 2002 to 2004 had Roto, Winkhaus or FUHR roller locks[19] Likely on newer doors
Peachtree A distributor says Peachtree used IPD/Citadel locks before 2002 and HOPPE after, with a faceplate the length of the panel[20] Likely after 2002
Marvin The same article says Marvin uses more than one lock maker[9] Check the stamp
Older FUHR locks HOPPE's replacement form asks for a HOPPE or FUHR logo[4] Logo only; measure before ordering

Brand by brand: Therma-Tru multipoint locks, Weather Shield door locks and Peachtree door lock replacement.

Close-up of a stainless lock faceplate out of the door, with the HOPPE logo stamped on it and circled.
Figure 5. The stamp near the latch and deadbolt names the lock maker. The door brand alone doesn't. Shown: a HOPPE faceplate out of the door.

Replacing HOPPE parts: what you can buy on its own

Most HLS 9000 parts are sold on their own, so a failed piece rarely means a whole new lock. The gear comes as one piece with its bottom extension; the top and middle extensions, strikes, handle set, spindle and cylinder are separate. HOPPE doesn't list the small gears or springs inside the lock case as parts, so a worn case is replaced as a unit.

  • Gearbox (gear): match mode, backset, deadbolt throw, handle height, point type and position, faceplate width and end shape. HOPPE's own catalog tells people replacing an existing gear to call their HOPPE representative rather than order from the tables[1]; our HOPPE part finder asks only the measurements the part needs and converts point positions for you. The step-by-step choice is on HOPPE multipoint lock replacement.
  • Handle set: HOPPE's HLS One catalog says any HLS 9000 swing-door set fits the HLS 9000 and HLS One[3]; it must still suit your door thickness. HOPPE, Amesbury Truth and Truth Sentry share a 3-5/8 in (92 mm) handle-to-cylinder spacing, but sets don't swap between brands. Screw pattern, cylinder position and door thickness differ. HOPPE's curved levers (München and others) come as one left-hand and one right-hand lever, so one set fits either door; fit both pointing toward the hinges.
  • Spindle: 5/16 in (8 mm) square, one-piece or two-piece (split) for set-screw handles.
  • Key cylinder: euro profile, sized by two lengths from the center of the fixing-screw hole. Therma-Tru's packet says HOPPE cylinders supplied with its doors use the Schlage C keyway and can be rekeyed[6]. See how to measure a euro cylinder and how to replace a euro cylinder.

Mount the gear with stainless steel screws only[1], and hand-tighten them: Therma-Tru's packet says too much force binds the drive rail[6]. The full swap is in how to replace a multipoint door lock; gear only, multipoint lock gearbox replacement.

HOPPE multipoint lock troubleshooting

Start with the door open. HOPPE's troubleshooting guide calls a lock that works with the door open fully functional: if it only fails with the door shut, the fault is how the door meets the frame, not the lock[5]. Hold the trigger in, lift the handle and turn the thumbturn. Then retract everything before you close the door, or the bolts will hit the frame.

HOPPE's guide lists ten problems, the same ten as Therma-Tru's packet[5]:

Symptom on a HOPPE door First check Full fix
Locks with the door open, not shut Strikes and hinges: the points are missing their holes (strike plates explained) door won't lock
Handle won't lift with the door shut Press the door in its closing direction (in toward the frame on a door that opens inward; pull it toward you on one that opens outward) and lift again multipoint lock problems by symptom
Key or thumbturn won't turn Is the handle fully up? Then loosen the backplate screws half a turn: crooked plates bind the cylinder key won't turn in the lock
Deadbolt won't fully throw Lift the handle fully first (HOPPE's advice on automatic gears), then check that the deadbolt hole in the strike lines up adjust the strike plate
Handle sags or clicks Handle loose on the spindle, or a worn gear spring drooping door handle fix
Set screws won't go into the handle The two-piece shaft is assembled the wrong way round, so the screw can't reach its groove loose door handle fix
Bottom point moves, top doesn't The joint: the teeth must mesh with a gap of less than 3 teeth[1], and the joint screw must be in replacing the lock
Deadbolt stuck out, door won't open Key or thumbturn back fully first, then handle down while pressing the door in its closing direction lock stuck closed
Door rattles or leaks air Rollers, strikes or hinges need adjusting (next section) patio door repair
Key doesn't work in the cylinder Try the spare key; if neither works, suspect a worn cylinder replacing the euro cylinder

HOPPE's catalog says a trigger turned the wrong way stops the lock throwing: pull it out, turn it 180 degrees and let it spring back so it slopes like the latch[1]. Locksmiths report that HOPPE and Amesbury Truth gearboxes carry their own return spring, so a handle that stays down with the handles off points to the gear. French doors: see French door lock repair.

HOPPE's HLS One catalog calls those kit parts self-lubricating, needing very little maintenance[3]; HOPPE names no lubricant. If yours is stiff, use the same type that's already on it (grease where there's grease), graphite only in the keyway, avoid silicone unless your lock's maker names it, and don't use WD-40 as the lubricant (door lock sticking).

Adjusting a HOPPE door: rollers, hinges and the auto-release

A HOPPE door can usually be pulled back into line without new parts:

  • Roller points: each roller has an off-center cam that moves about 0.04 in (1 mm) either way. HOPPE's roller sheet says to turn the dot on the roller toward the hinge side to squeeze the seal more, with a 5/32 in (4 mm) hex key[12].
  • Adjustable hinges: HOPPE's hinges move the door about 1/8 in (3 mm) up or down, or toward and away from the hinge side, with a 3/16 in (4.8 mm) hex key[13]; see door adjustment.
  • Auto-release roller (automatic gears): HOPPE's catalog says it moves only up and down in its slot. Loosen it with a 3 mm hex key, set it about 9/64 in (3.5 mm) from the auto-release strike, and retighten[1]. Removing it makes the lock semi-automatic.

Parts by problem

We sell HOPPE HLS 9000 parts, not HLS 7 gears or HLS One kits. Browse all HOPPE door hardware, or start from the problem:

Problem Part
Worn or broken gearbox multipoint lock gearboxes, such as the HOPPE HLS 9000 tongue gear or automatic tongue gear. Case only, for a manual lock: HOPPE HLS 9000 gearbox replacement (lock case only)
Damaged top extension or joint HLS 9000 tongue top extension, extension seam cover plate
Bent or worn strike HLS 9000 latch and deadbolt strike, tongue strike, all multipoint strike plates
Door sagging, points missing HOPPE adjustable door hinge
Worn handles or new finish multipoint lock handle sets, such as the HOPPE München narrow-plate set
Worn spindle or lost set-screw key HOPPE 5/16 in (8 mm) split spindle, HOPPE 3 mm hex wrench
Lost keys or stiff cylinder HOPPE euro cylinder, key outside, HOPPE rekey kit (HOPPE euro cylinders; HOPPE supplies it for trained professionals)
Second door of a pair HLS 9000 inactive shootbolt gear
Handles off, door still to work HOPPE construction handle (fits the 5/16 in (8 mm) hub)

When to call a pro

Call a locksmith or door installer when the door won't open and the steps on the stuck-closed page haven't freed it, when the frame or door is split or badly bowed, or when the gear has to come out of a door you can't take off its hinges. Prying at a locked multipoint bends extensions and strikes.

If a person or child is locked in a room or the house and can't get out, or there's a fire or other emergency, call 911 first. Only work on locks on your own door.

Check the door's warranty before you buy parts: some door makers cover the multipoint lock.

Common questions

How do you pronounce HOPPE?

HOPPE is a German family name, and in German it's said roughly "HOP-uh", with a short o and a soft ending. The capital letters are simply how the company writes its name. In the US the company trades as HOPPE North America, sometimes listed as HOPPE USA, based in Fort Atkinson, Wisconsin. If you're asking a supplier for parts, the system name (HLS 9000 or HLS 7) matters more than the pronunciation.

Where are HOPPE multipoint locks made?

HOPPE says its HLS 9000 multipoint system is made in the United States. HOPPE North America has its manufacturing plant and offices in Fort Atkinson, Wisconsin. The wider HOPPE Group runs eight plants across Europe and the US. If you need to know where a specific part was made, check the label on its packaging.

Who owns HOPPE?

HOPPE North America is part of the HOPPE Group, a family-owned company founded in 1952 and based in Switzerland. HOPPE's company page describes the group as having more than 2,500 staff and eight plants in Europe and the US. It makes handles and locking hardware for doors and windows, and the US business makes the HLS 9000 and HLS 7 multipoint systems.

Where can I buy HOPPE multipoint lock parts?

Door makers fit HOPPE locks at the factory, and replacement parts come through parts suppliers. We sell HOPPE HLS 9000 gears, extensions, strikes, handle sets, spindles and cylinders: see all HOPPE parts. Our HOPPE finder asks for only the measurements the part needs. We don't stock HLS 7 gears or boxed HLS One kits.

Is a HOPPE lock the same as a FUHR lock?

No, but they are linked. FUHR is a German lock maker; HOPPE sells FUHR's electronic Multitronic lock in North America, and HOPPE's replacement form asks whether your faceplate says HOPPE or FUHR. So a FUHR-stamped lock is worth measuring for a HOPPE replacement, though the logo alone doesn't prove a match. Measure it the same way: backset, deadbolt throw, handle height, faceplate width and each point's position.

Can I replace just the gearbox on a HOPPE lock?

Yes. On an HLS 9000 the gear comes as one piece with its bottom extension and is sold on its own, so the top extension, strikes and handles can stay if they're sound and match. Match the gear's code: mode, backset, deadbolt throw, handle height, point type and position, and faceplate. HOPPE doesn't list the small gears inside the case, so the case is replaced, not repaired.

Sources

  1. HLS 9000 Multipoint Swing Door Hardware, Edition 7, 12/2019 (archived), HOPPE
  2. HLS 7 Series Multipoint Hardware System, Edition 3, 02/2020 (archived), HOPPE North America
  3. HLS One Catalog/Brochure, Edition 5, 01/2020 (archived), HOPPE North America
  4. Multipoint Replacement Questionnaire, 2016 (archived), HOPPE
  5. Troubleshooting Guide, Multipoint Swing Door Hardware, 2015 (archived), HOPPE
  6. Multipoint Lock System (MPLS) installation packet (archived), Therma-Tru
  7. ARRONE Window Hardware for French Casements, 08/2018, company page (archived), HOPPE North America
  8. What to know about residential multipoint locks, Locksmith Ledger
  9. Multi-Point Locking Hardware (Peter Yost, 2020), GreenBuildingAdvisor
  10. Kolbe Expands Hoppe Hardware Selection (press release, November 2023), Kolbe Windows & Doors
  11. Electronic Multipoint Lock installation (FUHR multitronic), 08/2018 (archived), HOPPE / FUHR
  12. Adjustment Instructions for Roller Multipoint, R01 (archived), HOPPE
  13. Adjustable Hinge Adjustment Instructions, Rev. 06 (archived), HOPPE
  14. Impact-Rated Doors Product Data Sheet, October 2023, Simpson Door Company
  15. Pivot Door System, Simpson Door Company
  16. Loewen Swinging Terrace Doors (Loewen dealer), WindowCraft
  17. Door Hardware, Loewen
  18. 810 Hoppe 3-Point Gear Box and Extension, for Hurd Doors 2005 and Prior (listing), Window Parts Center
  19. Replacing Multipoint Locks in Weather Shield Doors Manufactured Prior to 2004, All About Doors & Windows
  20. Peachtree Lock Hardware, All About Doors & Windows

Help identify my part

Send the part number, measurements or photos of your old hardware. We’ll review your request and reply by email within 1 business day.

Your photos are stored privately and used to help identify your part. Privacy policy