Free US shipping90-day free returns · prepaid labelFit Guarantee · how it works
Shootbolt Instant identifierIdentify part

6 products · 82 versions

French Door Flush Bolts

French door flush bolts hold the second door of a pair at the top and bottom. Rods, guides, rod locks and handle-operated shootbolts.

Not sure which part? Use our instant part identifier

Filter
Not sure which part? Instant identifier or send us a photo.
Part type
Backset
6 products

Before you order: 3 checks

HOPPE's catalog calls the flush bolt the Inactive Flushbolt, its mechanism the rod lock or mortise flushbolt and the handle-operated version the inactive shootbolt, and it calls the second door the inactive panel, which Andersen and Marvin call the passive door.

  1. Test the lock with the doors open

    On a handle-operated second door, open both doors, lift the handle and turn the thumb-turn. The shootbolts should come out 3/4" (20 mm) or 1" (25.4 mm) and should not go back in when you push the handle down; then unlock and pull them in before you close the door. If the lock passes, look at the shootbolt strike plates and the hinges before you order a gearbox.

  2. Flush bolt or handle-operated lock?

    Look at the second door's handle. A handle that lifts, with a thumb-turn inside and no keyhole outside, usually means a handle-operated shootbolt lock: an inactive gearbox with a top extension. A fixed handle that does not move usually means a flush bolt in the door edge: a rod lock, rods and rod guides, which are different parts.

  3. Measure the rod's thickness, not only its length

    HOPPE rods are 5/16" (8 mm) or 3/8" (9.5 mm) thick, and some lengths are close: a 40-3/4" (1035.5 mm) rod is 5/16" and a 40-7/8" (1038.7 mm) rod is 3/8". Measure the thickness first, then the overall length. Every rod lock here is listed for 5/16" (8 mm) rods, and the rod guide, from $1.14, comes in one version for each thickness.

Compare the 6 flush bolt parts

What you choose on each page, how many versions it has and where its price starts. Every part number is in the list below.

PartYou chooseVersionsFrom
HOPPE flush bolt rod guide for the second door, polyamideSize: For 5/16", For 3/8"2$1.14
HOPPE flush bolt rod for the second door, stainless steelSize: 16 choices16$17.28
HOPPE flush bolt rod lock for the second door, stainless steelSize: 15/16", 1", 1-3/16" · Throw: 3/4", 1"4$79.99
HOPPE inactive gearbox for the second doorBackset: 1-3/8", 1-3/4", 2-3/8", 2-3/4" · Faceplate & shootbolt throw: 5 choices · Build: 2 choices18$149.99
HOPPE top extension with shootbolt, inactive second doorLength & locking points: 13 choices · Faceplate & shootbolt throw: 4 choices40$79.99
HOPPE bottom extension with shootbolt, 17-1/16" (434 mm)Faceplate & shootbolt throw: 2 choices2$69.99
All 82 part numbers on this page

Flush bolts for the second door of a French pair

Two ways to lock the second door

On a pair of doors the main door locks into the second door, so the second door has to be held firm at the top and the bottom. HOPPE does that two ways. A flush bolt sits in the edge of the second door and drives rods up into the head and down into the sill. An inactive door shootbolt lock does the same job from a handle: turning the handle on the second door throws its shootbolts. This page holds the parts for both.

Rods, rod guides and the rod lock

The flush bolt has three parts. The rod lock is the mechanism in the door edge, sold by rod backset, 15/16" (24 mm), 1" (26 mm) or 1-3/16" (30 mm), and by throw, 3/4" (20 mm) or 1" (25.4 mm). The rods are 5/16" (8 mm) thick and come in several lengths; measure the old rod end to end and compare it with the lengths listed. Rod guides keep the rods straight inside the door and come for 5/16" (8 mm) or 3/8" (9.5 mm) rods.

Handle-operated shootbolt locks

The inactive door shootbolt lock is a gear plus a top extension (2-piece), or a gear plus top and bottom extensions (3-piece). Match the backset, the faceplate width and the shootbolt throw, 3/4" (20 mm) or 1" (25.4 mm), to the lock on your door. The second door of a pair usually takes a second-door handle set, with a thumb-turn half cylinder on the inside only.

Choosing the right one

How to read the options you will see on these products.

Throw

How far the bolt sticks out of the faceplate when it's locked. HOPPE dead bolts throw 1" (25.4 mm) or 9/16" (14 mm); shootbolts throw 3/4" (20 mm) or 1" (25.4 mm).

How to measure: Lock the door while it's open and measure how far the bolt sticks out past the faceplate.

Backset

How far the handle sits from the edge of the door: from the face of the metal strip on the door edge (the faceplate) to the center of the handle hole. HOPPE HLS 9000 locks come in 1-3/8" (35 mm), 1-3/4" (45 mm, the standard), 2-3/8" (60 mm) and 2-3/4" (70 mm).

How to measure: Open the door. Measure from the face of the metal strip on the door edge to the center of the square handle spindle hole.

Faceplate width

The long metal strip you see on the edge of the door when it's open. HOPPE makes it 5/8" (16 mm) or 3/4" (20 mm) wide. The gear and the extensions of one lock must have the same width.

How to measure: Measure straight across the metal strip on the door edge: about 5/8" means 16 mm; about 3/4" means 20 mm.

Build

• 2-piece: gear + top extension. • 3-piece: gear + top extension + bottom extension (the bottom extension is sold separately).

Length & locking points

HOPPE sells a multipoint lock in pieces: the gear (the middle part, with the handle and key) plus a top extension, and on some locks a middle or bottom extension. Gear length + extension lengths = the overall length. Each extension length comes with its locking points at fixed heights.

How to measure: Measure your old extension end to end. HOPPE gives each bolt's height from the center of the handle, so measure from the handle center up to the middle of each bolt.

Questions

Which french door flush bolts do I need?

If you have the part number, from the box label or the paperwork that came with the door, search it above. HOPPE does not print part numbers on the parts themselves, so otherwise match the measurements in the guide above. Not sure? Use our instant part identifier to confirm the part before you order.

How do French door locks work at the top and bottom?

The second door is bolted into the frame at the top and the bottom, and the main door then locks into the second door. HOPPE does that two ways. A flush bolt sits in the edge of the second door and drives rods up into the head and down into the sill. An inactive door shootbolt lock does the same job from a handle: lifting the handle throws the shootbolts, and the inside thumb-turn locks them. This page holds the parts for both.

Which parts do I need to replace a HOPPE French door flush bolt?

The flush bolt is sold as separate parts, so order the one you need. In the door are the rod lock, which is the mechanism in the door edge, the rods and the rod guides. In the frame is the rod socket a rod locks into. Pick the rod lock by rod backset and throw, the rod by thickness and overall length, the guide by rod thickness and the socket by bolt throw. Every rod lock here is listed for 5/16" (8 mm) rods.

What is a passive (inactive) door, and how does it lock?

It is the second door of a French pair: the one that can only be opened after the main door. HOPPE calls it the inactive panel, and Andersen and Marvin say passive. It has no latch or deadbolt. Bolts into the head and sill of the frame hold it shut, worked by a flush bolt in the door edge or by a handle with a thumb-turn inside and no key cylinder outside. More terms are in the multipoint lock glossary.

How do I measure a flush bolt rod?

Measure the old rod end to end, then measure how thick it is. HOPPE lists each rod by its overall length, from 23-5/8" (599.6 mm) to 78-7/8" (2003.9 mm), and by thickness, 5/16" (8 mm) or 3/8" (9.5 mm). Check both together, because some lengths are only 1/8" apart and are different thicknesses: a 40-3/4" (1035.5 mm) rod is 5/16", and a 40-7/8" (1038.7 mm) rod is 3/8". See every rod length.

Why won't the second door of my French doors stay shut?

The second door has no latch or deadbolt. Its top and bottom bolts are all that hold it shut, so check them first. Open the door and throw the bolts: on HOPPE's handle-operated lock the shootbolts should extend 3/4" (20 mm) or 1" (25.4 mm). If they do, look at the rod socket or shootbolt strike in the frame and at the hinges.

Every order: free US shipping · 90-day free returns with a prepaid label · if our part identifier said it fits and it doesn't, we pay the return. Shipping · Returns

Help identify my part

Send the part number, measurements or photos of your old hardware. We’ll review your request and reply by email within 1 business day.

Your photos are stored privately and used to help identify your part. Privacy policy