6 products · 129 versions
Euro Profile Cylinders
Euro profile cylinders are the keyed part of a multipoint lock. Replace one for a lost key, a stiff lock or a new finish.
Not sure which part? Use our instant part identifier
Nothing matches every filter.
Before you order: 3 checks
Sellers also write euro cylinder, Euro profile cylinder or profile cylinder; HOPPE's catalog calls the keyed one the 90 Degree Crescent Knob Keyed Cylinder (a full or key/knob cylinder), the one with no key a half cylinder or thumbturn cylinder, and the retaining screw the Cylinder Screw.
Lift the handle fully, then try it with the door open
On a HOPPE lock you lift the handle to throw the bolts, then turn the key or thumb-turn, so try that with the door open. If it locks easily open but not shut, the door is out of line with its frame and the cylinder is not the part. Look at the strike plates and the hinges first.
Only the knob or a screw?
A loose or missing thumb-turn knob does not need a new cylinder. The knob set screw (from $2.99) holds the knob on, and the thumb-turn knob is sold on its own (from $34.87). A lost retaining screw (from $1.01) is picked by the lock's backset.
Key outside, or thumb-turn only?
A full cylinder goes through the door with a key outside and a knob inside. A half cylinder has its body on one side of the retaining screw hole only, and no key. Check which one you have before you measure: on a half cylinder the outside length is 3/8" (10 mm) on every version.
Compare the 6 cylinders and cylinder parts
What you choose on each page, how many versions it has and where its price starts. Every part number is in the list below.
| Part | You choose | Versions | From |
|---|---|---|---|
| HOPPE Euro profile lock cylinder, key outside, knob inside, 90° turn | Length (inside / outside): 10 choices · Finish: 10 choices | 60 | $99.99 |
| HOPPE cylinder knob set screw, holds the thumb-turn knob | Version: 2 choices | 2 | $2.99 |
| HOPPE Euro profile half cylinder, thumb-turn knob, no key, 3/8" (10 mm) outside | Length (inside / outside): 5 choices · Finish: 10 choices | 36 | $89.99 |
| HOPPE cylinder retaining screw, holds the cylinder in the lock | Version: 2 choices | 2 | $1.01 |
| HOPPE rekey kit with pins and springs, for locksmiths | One version | 1 | $399.99 |
| HOPPE cylinder thumb-turn knob, Euro profile, Crescent, H, V or L | Shape: Crescent Knob, H Knob, L Knob, V Knob · Finish: 12 choices | 28 | $34.87 |
All 129 part numbers on this page
- HOPPE Euro profile lock cylinder, key outside, knob inside, 90° turnAntique Brass: 3141933 · Matte Black: 3141984, 3442390, 3442461, 3647352, 3833833, 3833841, 40006585 · Oil-Rubbed Brass: 3141941, 3442411, 3442488, 3636936, 3636987, 3637031, 3637082, 3637171, 3637218, 3637251 · Pure White: 3141976 · Resista® Antique Nickel: 3142629 · Resista® Brushed Chrome: 3141909, 3636961, 3637015, 3637066, 3651301, 3651319, 3739687, 3967719, 3967727 · Resista® Polished Brass: 3142637, 3442357, 3442429, 3636928, 3636979, 3637023, 3637074, 3637162, 3637200, 3637242 · Resista® Polished Chrome: 3141925 · Resista® Satin Nickel: 3141917, 3442402, 3442470, 3636944, 3636995, 3637040, 3637091, 3637189, 3637226, 3637269 · Rustic Umber: 3141968, 3570367, 3584072, 3636952, 3637007, 3637058, 3637103, 3637197, 3637234, 3637277
- HOPPE cylinder knob set screw, holds the thumb-turn knob3475773, 3860209
- HOPPE Euro profile half cylinder, thumb-turn knob, no key, 3/8" (10 mm) outsideAntique Brass: 3141853, 3745972 · Matte Black: 3141896, 3442533, 3732522, 3738553 · Oil-Rubbed Brass: 3141861, 3442550, 3637306, 3637357, 3637390 · Pure White: 3141888, 3745964 · Resista® Antique Nickel: 3142565, 3733752 · Resista® Brushed Chrome: 3141829, 3637285, 3637331, 3651298 · Resista® Polished Brass: 3142611, 3442496, 3637293, 3637349, 3637381 · Resista® Polished Chrome: 3141845, 3733744 · Resista® Satin Nickel: 3141837, 3442541, 3637314, 3637365, 3637402 · Rustic Umber: 3141870, 3637322, 3637373, 3637411, 3650551
- HOPPE cylinder retaining screw, holds the cylinder in the lock2406936, 8773863
- HOPPE rekey kit with pins and springs, for locksmiths3459001
- HOPPE cylinder thumb-turn knob, Euro profile, Crescent, H, V or LAntique Brass: 11699802, 3643335, 3643360 · Brushed Chrome: 11699814 · Matte Black: 11699759, 3524707, 3643431 · Oil-Rubbed Brass: 11699760, 3524686, 3643407 · Polished Chrome: 11699826 · Pure White: 11699845, 3400202, 3643423 · Resista® Brushed Chrome: 3524660, 3643378 · Resista® Polished Brass: 11699796, 3643327, 3643351 · Resista® Polished Chrome: 3643343, 3643386 · Resista® Satin Nickel: 11699772, 3524678, 3643394 · Rustic Umber: 11699784, 3524715, 3643440 · Stainless Steel: 3857018
Euro cylinders and thumb-turns for multipoint doors
Full or half cylinder
A full cylinder takes a key on the outside and has a thumb-turn knob on the inside. A half cylinder has the thumb-turn only and is used where there is no keyhole outside, such as the second door of a French pair. Both slide into the lock through the door edge and are held by one retaining screw, so changing a cylinder doesn't mean taking the lock out of the door.
Measuring cylinder length
Euro cylinders are measured from the center of the retaining screw hole: an inside length and an outside length. Take out the screw in the door edge below the latch, turn the key or knob slightly so the cam lines up, slide the cylinder out and measure from the screw hole to each end. Lengths start at 1-1/4" (31.5 mm) a side, and each one is listed with the door thickness HOPPE pairs it with.
Knobs, screws and rekeying
Thumb-turn knobs come in crescent, H, L and V shapes and several finishes. The retaining screw comes in two lengths: 1-15/16" (50 mm) for 1-3/8" or 1-3/4" (35 or 45 mm) backset locks, and 2-15/16" (75 mm) for 2-3/8" or 2-3/4" (60 or 70 mm) backset locks. The rekey kit is for setting a cylinder to a new key.
Choosing the right one
How to read the options you will see on these products.
Cylinder length
A Euro (keyhole-shaped) cylinder is measured from its center screw: inside length (A) and outside length (B). Pick by door thickness, where the groove sits in the door edge, and the backplate. Full cylinders take a key outside and a thumb-turn inside; half cylinders have a thumb-turn only.
How to measure: Take out the screw on the door edge below the latch, remove the cylinder, and measure from the screw hole to each end.
Finish
The color and coating. The code in brackets is HOPPE's finish code. Resista® (codes ending -R) is HOPPE's protective finish.
Guides for this page
Written from the manufacturers' own catalogs and installation sheets.
Questions
Which euro cylinders do I need?
If you have the part number, from the box label or the paperwork that came with the door, search it above. HOPPE does not print part numbers on the parts themselves, so otherwise match the measurements in the guide above. Not sure? Use our instant part identifier to confirm the part before you order.
How do I measure a euro cylinder?
Measure from the center of the retaining screw hole to each end of the cylinder body. That gives two numbers: inside length (A) and outside length (B). Take out the screw in the door edge below the deadbolt, turn the key or knob slightly so the cam lines up, slide the cylinder out and measure. On the knob side, measure to the end of the body, not the knob. HOPPE lists 1-1/4" / 1-1/4" (31.5 / 31.5 mm) as typical for a 1-3/4" (44.5 mm) door.
Are euro profile cylinders a standard size?
No. The shape is shared, but the length is not. A Euro profile cylinder has a pear-shaped cross-section and is held by one screw through the door edge. Its length is picked by door thickness, where the groove sits in the door edge, and the handle backplate. HOPPE's key-and-knob cylinder here comes in ten inside and outside length pairs, from 1-1/4" / 1-1/4" (31.5 / 31.5 mm) up to pairs for a 3" (76.2 mm) door. Measure both sides; they are not always equal.
Can a HOPPE euro cylinder be keyed to match my other locks?
Usually, if your other locks use a Schlage C key. The HOPPE key-and-knob cylinder has a Schlage C, 5-pin keyway and comes with 2 keys. HOPPE's catalog lists a rekeying kit and Schlage pins for its cylinders, so a locksmith can usually set one to a 5-pin Schlage C key you already have. The rekey kit on this page is for locksmiths and installers. The half cylinder has no key, so there is nothing to match.
What is a half cylinder used for?
A door with no keyhole outside, such as the second door of a French pair. A half cylinder has a thumb-turn knob inside and no key. Its body sits on one side of the retaining screw hole, and the outside length is 3/8" (10 mm) on every version, so you pick by inside length and finish. HOPPE lists 1-1/4" (31.5 mm) as typical for a 1-3/4" (44.5 mm) door. See the HOPPE half cylinder, from $89.99.
Can I change the cylinder without taking the lock out of the door?
Yes. The cylinder is held by one retaining screw through the door edge, so the lock stays in the door. Take out that screw, turn the key or knob slightly until the cam lines up, and slide the cylinder out. HOPPE's instructions fit the new one from the inside of the door until its body is flush with the backplate, then the screw goes back in. Don't force the key or knob. HOPPE's sheet lists a Phillips screwdriver, a hex wrench and a ring wrench, with pliers recommended.
Every order: free US shipping · 90-day free returns with a prepaid label · if our part identifier said it fits and it doesn't, we pay the return. Shipping · Returns




