Therma-Tru door handles and handle sets: what fits the multipoint lock
By the Shootbolt team · · Updated
Short answer: Order grip-style trim (Forte, Prospect) from Therma-Tru's own store. On a lever-style door (Heirloom, Venture, Millennium), where you lift the handle to lock and the key sits 3-5/8 in (92 mm) below it, Therma-Tru's installation packet covers the HOPPE HLS 9000, so a HOPPE HLS 9000 handle set can fit. Check the stamp on the lock's faceplate before you order.
- First, the style: grip-style or lever-style (Figure 1)
- The lock decides what fits: read the stamp on the metal strip in the door edge (Figure 2)
- Tools: a 3 mm hex key and a Phillips screwdriver
- Under warranty? Ask Therma-Tru first; its warranty expects genuine parts
- Sweeps, plugs, sills: Therma-Tru's own store; we don't sell them
Which Therma-Tru handle set do you have?
Therma-Tru multipoint doors have a grip-style or a lever-style handle set. Other Therma-Tru doors have no multipoint lock, just a knob or lever and a separate deadbolt.
Reeb, a door distributor, lists five Therma-Tru handle set styles and the lock style behind each [3][4]:
| Style | Type | How it locks | Doors |
|---|---|---|---|
| Forte, Prospect | Grip-style | Turn the key or thumbturn 90 degrees; no lift. Deadbolt above the handle. | Single doors |
| Heirloom, Venture, Millennium | Lever-style | Lift the lever, then turn the key or thumbturn. Deadbolt below the handle. | Single or double doors |
| Knob or lever plus a separate deadbolt | Single-point | Latch and deadbolt; no long metal strip on the door edge | Any |
Grip-style doors aren't the HLS 9000 layout in Therma-Tru's packet, and we haven't found a source naming that lock's maker. Buy grip-style trim from Therma-Tru and skip the lever steps below.
A single-point door takes ordinary hardware. Measure the backset (how to measure door lock backset) and see how to fix a door handle. The rest of this page is about multipoint handle sets.
Check the lock in the door edge first
A handle set only works if it suits the lock. Read the stamp on the long metal strip (faceplate) in the door edge (Figure 2): Therma-Tru's packet covers the HOPPE HLS 9000 [1], but seller listings also show Ashland locks on Therma-Tru doors, and a Therma-Tru logo alone doesn't name the maker [2]. To identify, fix or replace the lock, see Therma-Tru multipoint locks.

What a replacement handle set has to match
For a lever-style door with a HOPPE HLS 9000 lock, a HOPPE HLS 9000 swing door handle set is the like-for-like match. If your door paperwork lists a HOPPE number, decode that part number first. Check each line:
| Check | What to look for | Why it matters |
|---|---|---|
| Handle-to-cylinder spacing | Center of the handle spindle to center of the key cylinder (Figure 3) | Spacing alone doesn't make sets swap between brands; screw pattern, cylinder position and door thickness must match too |
| Cylinder position | Key below the handle on the lever-style door | Emtek's multipoint price book lists Therma-Tru under its key-below-handle layout at 3-5/8 in (92 mm) [5] |
| Door thickness | Measure the door edge | HOPPE's HLS 9000 sets are made for 1-3/4 in (45 mm) doors [6] |
| Function | Active (key outside, thumbturn inside), inactive (second door of a pair) or fixed dummy | A double door needs an active set and an inactive set |
| Spindle | Square bar between the handles: 5/16 in (8 mm) on HOPPE | The wrong size slips |
| Lever shape | Curved levers point toward the hinges | HOPPE curved-lever sets come with one left and one right lever, so one set fits either door |

HOPPE sells its sets without a cylinder [6], so you can keep your old one; the cylinders supplied with Therma-Tru doors use a Schlage C keyway and can be rekeyed [1].
Genuine Therma-Tru parts and the warranty
If the door is still under warranty, start with Therma-Tru. Its owner's manual says the multipoint warranty applies only when all the listed parts are genuine Therma-Tru hardware [2]. It also excludes the handle finish and wear and tear, so a worn or tarnished handle may not be covered anyway. Read your terms in the Therma-Tru door warranty guide.
Clean handles with water and a soft cloth only: Therma-Tru's packet warns that brass cleaners and solvents strip the coating [1].
Therma-Tru door handle replacement: changing a lever set
The lock stays in the door; only the levers, plates and cylinder come off. Work with the door open and unlocked. These steps follow Therma-Tru's installation packet [1]:
- Take out the cylinder. Remove the cylinder screw in the door edge, below the deadbolt, then draw the cylinder out with the key turned slightly. See replacing a multipoint lock cylinder.
- Take off the levers. Loosen the set screw under the inside lever with the 3 mm hex key and pull both levers and the two-piece spindle out.
- Remove the plates. Undo the long inside-plate screws and lift both plates off.
- Fit the new plates loosely. Press the gaskets onto the backs of the plates and hang both loosely, with the long-screw heads on the inside of the door.
- Fit the levers. Slide the two-piece spindle into one lever, tighten its set screw flush with the 3 mm hex key, and push it through the plate and lock. Press the second lever on and tighten its set screw.
- Refit the cylinder. Slide it in from the inside until it's flush with the outside plate, refit the cylinder screw, then hand-tighten the plate screws.
- Test with the door open. Hold in the trigger, a small spring plunger beside the latch (the packet's "mishandling device"), lift the lever and throw the deadbolt. Retract everything before you close the door.
If a lever comes loose or droops later, see loose door handle fixes or drooping multipoint handle.
Other Therma-Tru door parts: sweeps, plugs and sills
For parts that aren't lock hardware, use Therma-Tru's own store. Its replacement parts section lists weatherstrip, 32 in (813 mm) and 36 in (914 mm) door bottoms and sweeps, frame and lite-frame screw plugs, corner seal pads, hinges and an inswing astragal boot [7]. Therma-Tru's site also has a replacement parts finder for sills and astragals [8]. We don't stock these.
Parts for this fix
Grip-style trim, and any set whose stamp you can't match, comes from Therma-Tru's store, not from us. For lever-style doors whose faceplate stamp and measurements match a HOPPE HLS 9000:
- Handle sets: multipoint handle sets, for example the HOPPE München set, narrow 1-1/4 in (32 mm) plate.
- Spindle: HOPPE 5/16 in (8 mm) two-piece spindle.
- Key cylinder and thumbturn: HOPPE euro cylinder, key outside and the thumbturn knob.
- While you wait: the HOPPE construction handle works the lock without finish trim; Therma-Tru's packet uses one during building work [1].
For a worn lock or gearbox, start at multipoint lock replacement by door brand.
When to call a pro
If someone is locked in and in danger, call 911. Most people can change a lever-style handle set themselves with the door open. Call a locksmith who works on multipoint doors if the door is locked shut, the set screw is seized, or the lock still fails the door-open test with the new handles on.
Common questions
Where can I find replacement handles for a Therma-Tru door?
Therma-Tru sells parts through its own online store and has a replacement parts finder on its website. If your door is lever-style (you lift the handle, then turn the key below it), Therma-Tru's installation packet covers the HOPPE HLS 9000, so HOPPE HLS 9000 swing door handle sets can fit. Check the stamp on the faceplate in the door edge and measure the handle-to-cylinder spacing before you order.
Can I replace just the door handle and keep the lock?
Yes. On a Therma-Tru multipoint door the handle set comes off without touching the lock in the door edge. You take out the key cylinder, loosen the set screw under the inside lever with a 3 mm hex key, pull both levers and the spindle, then undo the plate screws. Fit the new set the same way, and test it with the door open: hold the trigger in, lift the lever and throw the deadbolt, then retract every bolt before you close the door.
Can I put a different brand of handle set on a Therma-Tru multipoint door?
Only if it matches the lock inside the door. Matching the 3-5/8 in (92 mm) handle-to-cylinder spacing of the lever-style Therma-Tru layout isn't enough on its own: the screw pattern, cylinder position (above or below the handle) and door thickness must match too. Read the faceplate stamp, then use our lock identification guide if it's unclear.
Will a non-Therma-Tru handle set affect my warranty?
It can. Therma-Tru's owner's manual says the multipoint warranty applies only when all the listed parts are genuine Therma-Tru hardware. The same manual excludes the handle finish and normal wear and tear on the multipoint system. If the door is still under warranty and a part has failed, contact Therma-Tru before you buy anything else, and keep your proof of purchase.
What size hex key fits Therma-Tru door handles?
Therma-Tru's installation packet for its HOPPE-based multipoint lock uses a 3 mm hex key for the set screws in the levers. The set screw sits on the underside of the inside lever's neck. Other brands use other sizes; the full list by brand is in loose door handle fixes. Don't force a key that's slightly loose, or the screw head will round off.
Where do I buy Therma-Tru door sweeps, screw plugs and sills?
From Therma-Tru. Its online store lists weatherstrip, 32 in (813 mm) and 36 in (914 mm) door bottoms and sweeps, frame and lite-frame screw plugs, corner seal pads, hinges and an inswing astragal boot, and its website has a replacement parts finder for sills and astragals. We stock multipoint lock hardware, not Therma-Tru weatherstrip, sweeps or plugs.
Sources
- Therma-Tru Multi-Point Locking System installation instructions (HOPPE HLS9000), archived 2025-10-06, Therma-Tru
- Therma-Tru Owner's Manual and Limited Warranty, Therma-Tru
- Therma-Tru Handleset Styles, Reeb Learning Center
- Therma-Tru Handleset Functionality, Reeb Learning Center
- 2022 Price Book: Multi-Point Trim, Emtek
- HLS 9000 Swing Door Handle Catalog (11-2019), archived 2020-01-11, HOPPE
- Replacement Parts, Therma-Tru Store
- Components and Accessories, Therma-Tru