Motorized multipoint locks: how electric multipoint locks work
By the Shootbolt team · · Updated
Short answer: An electric multipoint lock has a small motor in its gearbox that throws or pulls back the hooks and bolts for you. Power comes from a separate supply and crosses into the door through a contact or cable at the hinge edge. A keypad, fob, intercom or access system tells the motor when to open.
- Power: a low-voltage supply for each lock (12 V DC on HOPPE and Winkhaus), with power run to the door
- Control: a switch signal from a keypad, fob reader or intercom
- Power cut: the makers' documents describe opening by key and the inside handle
- Retrofit: door and frame routing plus wiring: a door shop and an electrician
How does a motorized multipoint lock work?
A multipoint lock locks the door at several points along its edge from one gearbox (how a multipoint lock works). On most US doors you lift the handle to throw the points. A motorized (electric) lock does it with a motor. HOPPE North America's Electronic Multipoint Lock, built on FUHR's multitronic, is a typical set: the lock, a control module, a spring-loaded contact that carries power into the door, a magnet contact that senses the door is shut, cables and strikes[1]. You supply the power supply and the keypad (Figure 1).
FUHR's installation manual for the same lock gives the cycle[2]:
- Locking: about 3 seconds after the door closes, the motors throw every point.
- Opening from outside: a radio key, a keypad or other access device, or the key in the cylinder.
- Opening from inside: the lever handle as usual, a wall button, the intercom or the radio key.
FUHR warns not to work the handle while the motor runs.
Two kinds, and the makers' lines
In some lines the hooks throw themselves as the door shuts and the motor only opens; in others the motor locks and unlocks. Locks without a motor are compared on lever, key and automatic multipoint locks.
| Maker | Line | What the motor does |
|---|---|---|
| FUHR | autotronic 834, 836 | Automatic locking; motor unlocks[4] |
| FUHR (base of HOPPE's North American lock) | multitronic 881 | Fully motorized, built-in panic function[4] |
| Winkhaus | blueMatic EAV | Hooks throw as the door shuts; motor retracts them[5] |
| Winkhaus | blueMotion | Motor locks and unlocks[6] |
| KFV (SIEGENIA) | GENIUS EA, EB, CA/CB | Motor on a key-operated lock locks and unlocks[7] |
| KFV | AS 3500 with A-opener | Mechanical locking, motor release[7] |
| Roto | Safe Eneo CC | Motor opens and locks the main lock and all points[10] |
On Winkhaus's blueMatic EAV the deadbolt stays manual: one full turn of the key throws it[5]. The key cylinder matters too. The multitronic needs a free-running profile cylinder marked "FZG"[2], listed for HOPPE's version as a "360 degree" profile cylinder[1]. That isn't a HOPPE 90-degree cylinder, HOPPE's name for its HLS 9000 cylinder type, which stops after about 120 degrees when its cam is set (replacing a multipoint cylinder).
How power gets into the door
Makers bridge the gap with one of two parts on the hinge edge:
- Spring-pin contacts. HOPPE's brochure describes three silver-plated spring-loaded pins that pass 12 V DC from the frame into the door when it's shut, with no visible wires[3].
- A cable transition. A short protected cable loop crosses the gap at the hinge edge. Winkhaus's blueMatic manual recommends putting it on the hinge side, between the lower and middle hinges or about 4 in (100 mm) above or below the middle hinge, and hidden from tampering[5].
Each lock needs its own supply. Winkhaus says one supply can't run two blueMatic locks[5]. The figures differ by lock: 12 V DC at 3 A minimum for HOPPE's[1], a stabilized 12 V DC supply of at least 1.5 A for blueMatic[5], and 24 V DC in the wiring diagrams for the GENIUS exit locks[9].
Keypads, fobs, apps and access control
HOPPE's control module waits for a closed contact (a "dry" switch closure) of 1 second or less at its input[1]. A keypad, fingerprint reader or intercom provides that; app control comes through that access system, not the lock. GENIUS[8] and blueMatic[5] sets come with transponder, keypad and fingerprint options.
The multitronic control unit has more inputs[2]: a timer signal that holds the bolts back so only the latch works (day latch), an input that blocks all motor opening while it's on, and outputs to an alarm system and a powered door opener. A supplied switch turns automatic locking off[1].
A smart cylinder or cylinder turner is a different thing: it turns the key but can't lift the handle. Owners on the Home Assistant forum found no consumer smart lock that throws a lift-to-lock door's points[11]. That route is on smart locks for multipoint doors.
What happens in a power cut
None of the makers' documents we read calls its lock "fail-safe" or "fail-secure". What they say:
| Lock | What the maker says about power loss |
|---|---|
| HOPPE Electronic Multipoint (FUHR multitronic) | "Mechanical anti-panic egress – egress is assured with or without power", with mechanical overrides if power is lost[1]. FUHR: the key locks it with 4 turns and unlocks it from outside the same way[2]. |
| Winkhaus blueMatic EAV | A locked door can be worked by the cylinder or handle; from inside, the handle or key opens it "even possible in case of power failure"[5]. |
| KFV GENIUS GEP 2.2 and 2.3 (exit versions) | Opening with the lever handle in the direction of escape "is always possible"[9]. |
| Roto Safe Eneo CC | "Convenient opening from inside for a reliable exit in an emergency"[10]. |
Keep the key: from outside, it's the way in when the power is off. If the power fails while a blueMatic door is open, the latch may not hold it, so throw the deadbolt with the key[5]. FUHR says escape doors under the European exit standards (EN 179 and EN 1125) should have an emergency power supply[2]. How egress rules apply to locks on US homes is on locking a door from the inside or outside.
Can I add a motor to my door?
It depends on your lock (Figure 2):
- An automatic Winkhaus or KFV lock. Winkhaus sells the blueMatic motor housing loose to fit onto an autoLock AV3 or AV2[5]. Every KFV AS 3500 can take KFV's A-opener motor[7].
- A lift-to-lock lock such as HOPPE HLS 9000 or Amesbury Truth. We found no motor kit for these in either maker's documents: fit a whole motorized lock, or a smart cylinder and keep lifting the handle.
Either way, power has to reach the door. HOPPE warns: "Power must be supplied to each door opening. This can be problematic for some retro-fit applications."[1] The multitronic install has the door routed and drilled for the contacts and cable, and an electrician connecting the supply[2]. The first North American home install needed a millworker to modify the doors and frames, electricians to bring power, and a systems integrator to connect the keypad[3]. The lock must also suit the door: the HOPPE lock is 85.4 in (2170 mm) long, cuts down to 67 in (1702 mm), has a 1-3/4 in (45 mm) backset and a 5/8 in (16 mm) faceplate, and is handed[1]. Routing a door edge: euro groove explained.
The multitronic isn't built to pull a warped door straight. If it flashes red and green or beeps five times after trying to lock, open it with the key, not the handle, and check the door and strikes[2] (multipoint lock problems).
Parts for this fix
We don't sell motorized locks, motors, power supplies, keypads or access systems. For FUHR, Winkhaus, KFV or Roto, start with your door maker's dealer or the lock maker; for HOPPE's Electronic Multipoint Lock, HOPPE North America or a HOPPE door dealer. HOPPE offers door preparation files on request[1]. What we do stock is the manual hardware for HOPPE and Amesbury Truth locks.
When to call a pro
If someone is trapped inside and in danger, call 911. A motorized lock needs a door shop or finish carpenter for the routing, a licensed electrician for the power, and the access system's installer. Call a multipoint locksmith if neither the motor nor the key opens the door.
Common questions
Is an electric multipoint lock the same as a smart lock?
No. An electric (motorized) multipoint lock has a motor in the gearbox that moves every point, and it needs a power supply wired to the door. A smart cylinder or cylinder turner only turns the key, so on a lift-to-lock door you still lift the handle first. The smart-lock routes are on smart locks for multipoint doors.
Can I get out if the power goes off?
For the locks we read, the makers say so. HOPPE says its Electronic Multipoint Lock has mechanical anti-panic egress, assured with or without power. Winkhaus says the handle or key opens a blueMatic door from inside even in a power failure. SIEGENIA says the lever handle always opens its GENIUS exit versions in the escape direction. Keep the key for getting in. If someone is trapped and in danger, call 911.
Does a motorized multipoint lock need batteries?
The wired locks covered here run from a mains power supply, not batteries: 12 V DC for HOPPE's and Winkhaus's blueMatic, 24 V DC in SIEGENIA's GENIUS exit-lock diagrams. Each lock needs its own supply and power run to the door. Battery-powered smart cylinders are a different product (smart locks for multipoint doors).
How does the power get into a door that swings?
Through a part on the hinge edge. HOPPE's lock uses three spring-loaded pins on the door that touch a contact plate on the frame when the door is shut. Winkhaus and SIEGENIA use a cable transition, a short protected cable that crosses the gap, which Winkhaus recommends placing near the middle hinge.
Can I add a motor to my HOPPE or Amesbury Truth lock?
We found no motor kit for HOPPE HLS 9000 or Amesbury Truth lift-to-lock locks in either maker's documents. The options are a whole motorized lock, which means new door and frame routing and wiring, or a smart cylinder that turns the key while you still lift the handle. Winkhaus and KFV do sell motors that fit some of their own automatic locks.
Sources
- Electronic Multipoint Lock Quick Facts, 08-2018 (archived 2020-01-11), HOPPE North America
- FUHR multitronic 881 (Electronic Multipoint Lock) installation, operating and maintenance instructions, 08-2018 (archived 2020-01-11), HOPPE / FUHR
- Electronic Multipoint Locking brochure and case study, 08-2018 (archived 2020-01-11), HOPPE North America
- Motor locks: autotronic and multitronic, FUHR
- blueMatic EAV installation, operating and maintenance instructions, 03/2026 (PDF), Winkhaus
- Door locking system: mechanical and motorised systems (archived 2022-05-25), Winkhaus
- KFV product catalogue: multi-point locks and frame parts for timber doors, H4009.3093EN, 11.2020 (PDF, dealer-hosted copy), KFV / SIEGENIA
- GENIUS 2.2 electromechanical multi-point lock brochure, 2018-02 (PDF), SIEGENIA
- Electromechanical multi-point lock GEP 2.2 and 2.3: assembly instructions, H39.ELEKS014EN-02, 09.2026 (PDF), SIEGENIA
- Roto Safe Eneo information sheet, 06-2026 (PDF), Roto Frank of America
- Multi-point smart lock with support for locking without lifting the handle (forum thread), Home Assistant Community